Hotpoint Refrigerator Ice Makers
Find your part
Enter your model number or a part number and click "Search"
Popular Hotpoint Refrigerator Ice Makers
Your Price
$208.87
Ice Maker
PartSelect Number PS1993870
Manufacturer Part Number WR30X10093
This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- Ice maker not making ice
- See more...
Installation Instructions
Michael from Bradenton, FL
ice maker not working properly and door seal worn
Two screws held the icemaker on. You do not even have to take them all the way out to remove the IM. Replacement of the water valve was just as easy except they (parts manufacturer) updated the flange nut with a compression fitting and it took me a minute looking at it before I realize what was going on. The door seal could not be easier, no tools just a few minutes of time
Read more...
Your Price
$64.80
Dispenser Auger
2) Removed 5 screws total
3) (hardest part) JImmied a flat blade screwdriver into the left top side of the housing and pried gently to disengage the plastic holding clip. This only allows the left side of the housing to move up about a half-inch. Did the same on the right side and 'walked' the assembly out of the bin.
4) Removed the C clip and washer that holds the auger. and removed the auger assembly.
5) Before removing the screw at the end of the assembly, it is a good idea to take pictures of the ice crushing part of the assembly so that it goes back on correctly.
6) Removed the screw and carefully stacked the ice crush blades and washers.
7) Installed the ice crush blades on the new auger, re-installed the screw, washer and C clip.
8) Re-assembly is easy, you just need to set the end of the auger in the back of the ice bin and slowly re-install the housing portion. Read more...
PartSelect Number PS1018130
Manufacturer Part Number WR17X11939
When activated, the auger rotates and pushes ice out of the bin through the chute to the user.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Installation Instructions
robert from wesley chapel, FL
Plastic auger cracked. This part moves the ice in the bin forward to the dispenser
1) Removed the ice bin and emptied the ice.2) Removed 5 screws total
3) (hardest part) JImmied a flat blade screwdriver into the left top side of the housing and pried gently to disengage the plastic holding clip. This only allows the left side of the housing to move up about a half-inch. Did the same on the right side and 'walked' the assembly out of the bin.
4) Removed the C clip and washer that holds the auger. and removed the auger assembly.
5) Before removing the screw at the end of the assembly, it is a good idea to take pictures of the ice crushing part of the assembly so that it goes back on correctly.
6) Removed the screw and carefully stacked the ice crush blades and washers.
7) Installed the ice crush blades on the new auger, re-installed the screw, washer and C clip.
8) Re-assembly is easy, you just need to set the end of the auger in the back of the ice bin and slowly re-install the housing portion. Read more...
Your Price
$58.97
Ice Bucket Auger
It is not that hard to do the repair it just takes some patience and paying attention to details. Read more...
PartSelect Number PS964350
Manufacturer Part Number WR17X11705
The ice bucket auger is located within the ice bucket assembly in your freezer. It stirs and dispenses the ice in the bucket. You may need to replace the auger if your ice maker is noisy, or not dispensing ice. Disassembly of the ice bucket assembly is necessary to replace this part. Turn off power to the appliance before removing the ice bucket assembly to do this repair.
Fixes these symptoms
- Engine revs but auger will not turn
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- See more...
Installation Instructions
Tim from Newport News, VA
Plastic Auger blades broke in ice tray
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with small flathead screwdriver. Slide white top cover up and you will now see the metal blades and assembly. Auger is held in place with a metal c-clip and washer on the end. Use flat head screwdriver to pry off c-clip. Then you will see a nylon round slotted nut. The threads are reverse, use pliers and loosen nut. It is not that tight but pliers are needed. Then it all is loose and ready for removal. I slid all the blades off at one time and kept them stacked together. Slide out auger and clear flat shield cover. Install new auger, clear shield, and metal blade stack. When you put it all back together take a look at the long metal J-hook on the bottom make sure it is in the slot before you make everything tight. Failing to do this will prevent cubed ice from dispensing. It is not that hard to do the repair it just takes some patience and paying attention to details. Read more...
Your Price
$48.05
Ice Dispensing Drive Cup
Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
PartSelect Number PS964134
Manufacturer Part Number WR17X11459
This part is found at the end of the auger in the ice container - replace this part when the icemaker doesn't dispense ice.
Fixes these symptoms
- Clicking sound
- Ice maker dispenses too little ice
- Ice maker not making ice
- See more...
Installation Instructions
Fred from River Ridge, LA
Ice Maker stopped dispensing ice through Ice Maker Dispensor.
After taking Ice Maker's ice collection container out, I noticed that the plastic cup drive was broken. I did a websearch for repair and replacement parts for our GE refrigerator. I found PartSelect website easy to navigate and find the replacement part necessary...and placed an order.Once I received the shipment, I placed the Cup Drive into position and used the flat edge of a knife to allow the Cup Drive to slide into the tight-fitting position necessary. After positioning into place, I placed the ice collection bin back into the freezer...turned the ice-maker back on...and waited for ice to be made. A day later, the ice maker had produced enough ice to test the ice maker's dispensing mechinism. The cup drive worked perfectly...and ice began to be dispensed. The dispensor has been working ever since.
I also replace the ice and water filter...another very easy task...of unscrewing the old and replacing with the new filter. After replacing the filter, I let the water dispensor run for 2 minutes to flush all air out the system. The water dispensor work perfectly. Read more...
Your Price
$161.48
Ice Bucket and Auger Assembly
PartSelect Number PS11701245
Manufacturer Part Number WR17X23191
This part includes the blades/cutting assembly.
This ice container assembly is for refrigerators.
Ice container assembly stores the ice until needed and comes with the auger that rotates to move the ice into the dispenser chute. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker not making ice
- Ice maker won’t dispense ice
- See more...
Installation Instructions
Marshall from Yuma, AZ
auger was not working
This happened once before. The plastic auger broke. I had a local repair store order the auger and then install it into the bucket. The cost was much more than I paid PartSelect for the entire assembly. What could be easier--pop the old one out and put in the new--for a cheaper price.
Read more...
Your Price
$239.90
Refrigerator Ice Bucket and Auger Assembly
PartSelect Number PS11701246
Manufacturer Part Number WR17X23255
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- Ice maker not making ice
- See more...
Installation Instructions
Gunars from Arlington, TX
Plastic piece on front of ice bucket auger cracked an broke off
I just pulled the old Ice bucket assembly out and replaced it with the new one. Couldn't get any easier.
Read more...
Your Price
$25.47
Dispenser Crusher Cover
This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.
The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier. Read more...
PartSelect Number PS964165
Manufacturer Part Number WR17X11497
This part is white in color.
Fixes these symptoms
- Ice maker dispenses too little ice
- Ice maker dispenses too much ice
- Ice maker not making ice
- See more...
Installation Instructions
Bill from Cleveland Heights, OH
flap to ice dispenser would not close
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the solenoid. My fridge may be a newer model, but in any event it was much easier than that. Just below the touch pad for choosing water, ice, or crushed ice (above where the ice/water dispenses) there are three very small holes spaced about an inch a part. After unplugging the fridge, I stuck a small philips-head screw driver in each, freeing spring clips. That allowed the touch pad to come off. I then removed four screws to remove a plastic piece covering the chute, giving me access to the flap and solenoid. I just unplugged the solenoid from the circuit board on the back of the touch pad and then removed three screws to remove the old solenoid. I replaced it with the new solenoid and plugged it into the circuit board. The touch pad then snapped back into place.
The hardest part was figuring out how to get at the solenoid. After I found that pushing the clips in those three holes allowed me to remove the touch pad, it could not be any easier. Read more...
Your Price
$28.33
Ice Bucket - White
Without access to a friendly user website, I would have faced considerable delay in getting this part. Read more...
PartSelect Number PS3499784
Manufacturer Part Number WR30X10154
The ice bucket in your freezer collects the ice from the ice maker and stores it. If your old ice bucket is damaged you may want to replace it as it can leak. This product is made of white plastic and is approximately 13 inches in length and 9 inches wide at the widest point. This is an OEM part sourced directly from the manufacturer. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the damaged bucket, making sure to collect any broken pieces. Then, simply slide the new bucket in place.
Installation Instructions
Tom from Bradenton, FL
Ice bucket missing
I discovered the ice bucket missing from my rental unit at the beach. I was able to go online with my Blackberry, easily navigate your website using the model number to look up the part information , order it, and have it in place for the next renter. Without access to a friendly user website, I would have faced considerable delay in getting this part. Read more...
Your Price
$340.85
Ice Bucket and Auger Assembly
PartSelect Number PS783770
Manufacturer Part Number WR17X11447
This part holds the ice once it's released from the icemaker. When activated, the auger rotates and pushes ice out of the bin through the chute to the user.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Noisy
- See more...
Installation Instructions
Michael from Matthews, NC
Ice maker would not dispense and made a loud clunking sound
First I replaced a cone shaped piece at the rear of the auger. That worked for about 20 minutes and it snapped off the middle. Same as original problem. Then I replaced the whole damn bucket and auger assembly. Works like new. Should have done that 1st and saved $24 and a week.
Read more...
Your Price
$116.43
Auger Motor
PartSelect Number PS1993875
Manufacturer Part Number WR60X10258
This motor is used to activate the blades to crush the ice for dispensing. This part is now threaded with a left hand thread and the J nut is no longer required.
Fixes these symptoms
- Ice maker not making ice
- Ice maker won’t dispense ice
- Will Not Start
- See more...
Installation Instructions
Mark A. from Port Byron, IL
Bad Ice Auger Motor
Things I learned...remove only the two far left screws and one far right screw from the ice auger motor mounting plate. Disconnect both wiring harness connectors. With the assembly removed from the freezer, you'll need to get the motor seperated from the drive mechanism (fork). This was the most difficult part of the repair. The reason is that the fork (which is reverse threaded) cannot be unthreaded independantly of the motor shaft (ie. they both turn together). Locking pliers on the shaft only stripped metal from the shaft and did not supply enough torque to remove the fork. The way I finally did it was to take the old motor partially apart, then lock the gear case (keeping the shaft from rotating) with the motor's own splined internal rotor shaft. Once I finally got the fork apart from the motor shaft, swapping out motors was simple. You'll need to put the old plastic glove on the new motor to keep it dry. Also, the replacement motor I got from partselect.com did not come with threaded mounting bolt holes. Therefore, I had to use slightly larger self tapping screws I got from the hardware store. I also used locking washers as the assembly is subject to vibration.
Read more...
Related Parts
- All Hotpoint Refrigerator parts
- Hotpoint Refrigerator Brackets and Flanges
- Hotpoint Refrigerator Caps and Lids
- Hotpoint Refrigerator Circuit Boards and Touch Pads
- Hotpoint Refrigerator Compressors
- Hotpoint Refrigerator Dispensers
- Hotpoint Refrigerator Door Shelves
- Hotpoint Refrigerator Doors
- Hotpoint Refrigerator Drawers and Glides
- Hotpoint Refrigerator Elements and Burners
- Hotpoint Refrigerator Grilles and Kickplates
- Hotpoint Refrigerator Handles
- Hotpoint Refrigerator Hardware
- Hotpoint Refrigerator Hinges
- Hotpoint Refrigerator Hoses and Tubes
- Hotpoint Refrigerator Knobs
- Hotpoint Refrigerator Lights and Bulbs
- Hotpoint Refrigerator Motors
- Hotpoint Refrigerator Seals and Gaskets
- Hotpoint Refrigerator Springs and Shock Absorbers
- Hotpoint Refrigerator Switches
- Hotpoint Refrigerator Thermostats
- Hotpoint Refrigerator Trays and Shelves
- Hotpoint Refrigerator Valves
