Hotpoint Range Hardware
Popular Hotpoint Range Hardware
Your Price
$13.91
In Stock
Hotpoint Range Door Bumper - Black
PartSelect Number PS241365
Manufacturer Part Number WB2K15
Sold individually.
Your Price
$16.66
In Stock
Hotpoint Range Single Heating Element Support Clip
I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
PartSelect Number PS243701
Manufacturer Part Number WB2X9719
The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Paul from Canton, NY
broiling element had burned through, req. its replacement
First I removed the two screws that hold the element in place. I also removed a screw that held one end of a support bracket. I then pulled the element out about 3 inches and disconnected the two wires. Reversing these steps, I finished the element's replacement.I had noticed that the former element was sagging at the front end. I installed the additional clips (not original) on each forward end of the element for additional support. Read more...
Your Price
$8.54
In Stock
Hotpoint Range RECEPTACLE PUSH-IN
PartSelect Number PS752188
Manufacturer Part Number WB08T10026
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
Installation Instructions
Richard from Menifee, CA
No problems encountered.
Used nutdriver to remove screws holding cover over oven light socket, unclipped electrical connectors, removed socket by hand, then reversed the foregoing. Easy.
Read more...
Your Price
$13.70
In Stock
Hotpoint Range Top Electrode Mounting Clip
PartSelect Number PS3510420
Manufacturer Part Number WB01K10112
Sold individually.
Fixes these symptoms
- Gas igniter glows, but will not light
- Will Not Start
- See more...
Installation Instructions
Michael from Weatogue, CT
No spark at one burner
Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner casting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter.
Read more...
Your Price
$9.63
In Stock
Hotpoint Range Ignitor Mounting Screw
PartSelect Number PS234519
Manufacturer Part Number WB1X1293
Sold Individually.
Fixes these symptoms
- Little to no heat when baking
- See more...
Installation Instructions
CHRISTOPHER from REDMOND, OR
Oven Igniter Died
The only difficult part of the repair was getting the original screws out of the old igniter and oven gas arm. Once I drilled the old screws out the repair was done within 20 minutes.
Read more...
Your Price
$12.19
In Stock
Hotpoint Range SCREW 10-32 TR T
PartSelect Number PS222157
Manufacturer Part Number WB01T10008
This part is a replacement screw for your oven. It is made of black metal and is sold individually. This screw is approximately 1/4 inch in diameter and about 1/2 inch in length. It is designed to connect the different parts of your oven door. This part is an authentic OEM part sourced directly from the manufacturer.
Your Price
$8.30
In Stock
Hotpoint Range Screw
1. remove the first 4 screws and the fan's cover
2. remove the short screws from element convection assembly
3. gently pool both wires and disconnect the old element (two terminals)
4. carefully insert the terminals in the new element.
5. re-screw the short 4 screws (better to buy new ones with the assembly) They are available but sold separated.
6. fix back the fan cover,
re-connect the breakers and that's it! Read more...
PartSelect Number PS234427
Manufacturer Part Number WB1X1130
Sold Individually.
Installation Instructions
George from MILWAUKIE, OR
GE WB44T10086 Range Convection Element AP4358533 PS2321875 interrupted
after you disconnect the direct breakers and open the oven:1. remove the first 4 screws and the fan's cover
2. remove the short screws from element convection assembly
3. gently pool both wires and disconnect the old element (two terminals)
4. carefully insert the terminals in the new element.
5. re-screw the short 4 screws (better to buy new ones with the assembly) They are available but sold separated.
6. fix back the fan cover,
re-connect the breakers and that's it! Read more...
Your Price
$8.08
In Stock
Your Price
$12.21
In Stock
Hotpoint Range Screw
5 screws off the back
2 in the front - Husky screws in the front
panel clips - the top panel was opened.
1 more screw for starter switch
DONE - under 15 minutes. Read more...
PartSelect Number PS271689
Manufacturer Part Number WH2X930
This screw is sold individually.
Installation Instructions
Mikhail from Framingham, MA
8 screws and done
After taking off:5 screws off the back
2 in the front - Husky screws in the front
panel clips - the top panel was opened.
1 more screw for starter switch
DONE - under 15 minutes. Read more...
Your Price
$8.06
In Stock
Related Hotpoint Range Parts
- All Hotpoint Range parts
- Hotpoint Range Brackets and Flanges
- Hotpoint Range Caps and Lids
- Hotpoint Range Circuit Boards and Touch Pads
- Hotpoint Range Doors
- Hotpoint Range Drawers and Glides
- Hotpoint Range Drip Bowls
- Hotpoint Range Elements and Burners
- Hotpoint Range Grates
- Hotpoint Range Handles
- Hotpoint Range Hinges
- Hotpoint Range Igniters
- Hotpoint Range Insulations
- Hotpoint Range Insulations
- Hotpoint Range Knobs
- Hotpoint Range Lights and Bulbs
- Hotpoint Range Racks
- Hotpoint Range Seals and Gaskets
- Hotpoint Range Switches
- Hotpoint Range Thermostats
- Hotpoint Range Trims
- Hotpoint Range Valves
- Hotpoint Range Wire Plugs and Connectors