Hotpoint Range Wire Plugs and Connectors

Hotpoint Appliance Parts

Popular Hotpoint Range Wire Plugs and Connectors

Your Price
$24.52
  On Order
Hotpoint Range Surface Burner Terminal Block Kit
★★★★★
★★★★★
24 Reviews
PartSelect Number PS783534
Manufacturer Part Number WB17T10006
This kit includes the female contact with wires, terminal block and mounting clip.
Fixes these symptoms
Installation Instructions
Americus from Pittsburgh, PA
Burned out block
Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer. Read more...
Your Price
$31.61
  In Stock
Hotpoint Range Surface Burner Terminal Block Kit
★★★★★
★★★★★
20 Reviews
PartSelect Number PS242972
Manufacturer Part Number WB2X8228
Also known as receptacle.
Fixes these symptoms
Installation Instructions
Robert from Mt. Vernon, IN
The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes Read more...
Your Price
$78.35
  In Stock
Hotpoint Range Surface Burner Terminal Block Kit
★★★★★
★★★★★
6 Reviews
PartSelect Number PS232606
Manufacturer Part Number WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
Fixes these symptoms
Installation Instructions
Shaohui from East Lansing, MI
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe. Read more...
Your Price
$56.72
  In Stock
Hotpoint Range Terminal Block Kit
★★★★★
★★★★★
13 Reviews
PartSelect Number PS953027
Manufacturer Part Number WB17T10011
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Fixes these symptoms
Installation Instructions
jonathan from willow springs, IL
terminal block melted
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient Read more...
Your Price
$38.38
  In Stock
Hotpoint Range Terminal Block
★★★★★
★★★★★
5 Reviews
PartSelect Number PS232646
Manufacturer Part Number WB17X5113
This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.
Fixes these symptoms
Installation Instructions
Richard from Apex, NC
Heating element required continuous adjustments to work.
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder joint. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner. Read more...
Your Price
$8.06
  In Stock
Hotpoint Range CLIP RECEPTICAL
PartSelect Number PS1154856
Manufacturer Part Number WB02K10133
Fixes these symptoms
Your Price
$8.06
  In Stock
Hotpoint Range Terminal Block Clip
PartSelect Number PS232607
Manufacturer Part Number WB17X211
Your Price
$74.64
  In Stock
Hotpoint Range Power Terminal Block Kit
★★★★★
★★★★★
1 Review
PartSelect Number PS232636
Manufacturer Part Number WB17X5095
This kit comes with the terminal block, nuts and wires.
Installation Instructions
Bernard from N CHARLESTON, SC
no burnt wire
Replace part an wires Read more...
Your Price
$49.60
  On Order
Hotpoint Range HARNESS BURNER BOX
PartSelect Number PS2374075
Manufacturer Part Number WB24K10065
Your Price
$43.20
  In Stock
Hotpoint Range HARNESS HV
PartSelect Number PS1480999
Manufacturer Part Number WB18K10035
Installation Instructions
Michael from Weatogue, CT
No spark at one burner
Other writers have claimed that this is a "really easy" job. They apparently had one or more of: 1. Less used appliance. 2. Never spilled anything on the cooktop 3. Much better luck. In my case, the apparently faulty igniter absolutely would not pull out. I removed it by removing the burner retaining screws and prying under the burner casting. Having done that, I cleaned the igniter and tested it again. None of the igniters worked, and I could hear arcing under the cooktop, indicating one or more of the igniter HV wires had somehow grounded. After a fruitless search for instructions on raising the cooktop, I stumbled upon an envelope glued to the back of the range that told me to remove all four burners and igniters and to release the cooktop by inserting a thin screwdriver under the front edge about 3" from each end to release the spring clips. Several of the igniters were cemented in place with caramelized sugar and required some pretty vigorous prying to dislodge. If I had this to do again on a range that had been ridden hard, I wouldproactively order a full set of gaskets (they're fragile), the HV harness (even if it doesn't leak as mine did, the igniter connectors degrade from heat exposure), a set of electrode mounting clips (none of them were much use either), and enough igniters to replace any that don't work plus at least one. I pried out the recalcitrant igniters; in retrospect I should have crushed them because of the severe risk imposed by prying of breaking either a burner casting or the cooktop -- either of which are far more expensive than another igniter. Read more...

Related Hotpoint Range Parts