Whirlpool Ice Maker Parts

Whirlpool Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular Whirlpool Ice Maker Parts

Your Price
$126.15
  In Stock
Condenser Fan Motor Kit
★★★★★
★★★★★
(37)
PartSelect Number PS1957416
Manufacturer Part Number W10124096
This condenser fan motor kit includes a motor, fan blade, wire harness, and screws. Used in a refrigerator, the condenser fan motor moves the condenser fan blade to direct and move air across the condenser coil. Please note: The manufacturer has changed the appearance of the product from the original. The kit still functions the same as the original part. It is an OEM factory replacement. Make sure to unplug the refrigerator from the power source and wear gloves to protect your hands. Also, a helpful tip is to store food to prevent deterioration when the power is off.
Fixes these symptoms
  • Clicking sound
  • Freezer section too warm
  • Fridge and Freezer are too warm
  • See more...
Installation Instructions
Josue from Jacksonville, NC
Seven year old condenser fan was making noise when it was running.
The process to repair was very simple, I removed the back of the refrigerator to expose the motor area. I then removed three screws that held the condenser motor in place. once it was loose I detactched the electrical harness and removed the old motor. I then placed the new motor in place and secured it with the screws and reattached the new electrical harness that came with the new part. Once completed I reviewed it to make sure I didn't miss anything. I then replaced the cover over the motor area and enjoyed my success in repairing my own appliance with no added cost for labor, which would have been expensive I'm sure. The part purchased came with clear and consice instructions very easy to follow. Read more...
Your Price
$25.45
  In Stock
Water Tube Kit
★★★★★
★★★★★
(7)
PartSelect Number PS11730901
Manufacturer Part Number W10823511
This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
  • Ice maker not making ice
  • Leaking
  • Not dispensing water
  • See more...
Installation Instructions
Trent from Tacoma, WA
water dispenser started leaking
i wasn't sure it was the inlet valve unit because the leak was at the water dispenser in the freezer door. after some research it looked like the water inlet valve located in the back lower part of the refrigerator was the problem. to replace, take off the cardboard cover, about 6 screws, you have access to the water inlet valve, disconnect the hoses (i think it goes without saying that you should have turned off the water to the frig) replace the inlet valve, connect hoses, turn water back on and you'll be back in business. very easy repair. Read more...
Your Price
$33.32
  In Stock
Ice Maker Water Distributor Tube
★★★★★
★★★★★
(1)
PartSelect Number PS11738017
Manufacturer Part Number W10863947
The water distributor tube distributes water from the reservoir to the evaporator plate.
Installation Instructions
Gerald from ELMHURST, IL
The tunes were moldy and the pump didn't work.
The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years. Read more...
Your Price
$205.70
  In Stock
Ice Cutter Grid Complete Assembly
★★★★★
★★★★★
(8)
PartSelect Number PS11740334
Manufacturer Part Number WP2313637
If your freestanding ice maker is not producing ice properly, the ice cutter grid assembly may need replacing. The cutter grid is located within the main unit of the ice maker and contains thin, heated wires that slice the ice into cubes that are then deposited in the ice bin. If the cutter grid is broken, ice can back up within the ice maker. This part is sold as a complete assembly and is used with freestanding ice makers. Be sure to wear work gloves to protect your hands when completing this repair. This is an OEM part that sources directly from the manufacturer.
Installation Instructions
Brad from Bakersfield, CA
Grid Assembly had a broken wire and would not separate the ice sheets into cubes
I removed the 2 screws on each side of the grid and disconnected the electrical plugs attached to the grid. I slid the broken unit out. I then carefully slid the new unit in making sure not to pinch any of the electrical wires. I replaced the mounting screws, plugged the 3 connectors back into place and turned the ice maker back on. I had ice cubes within a couple of hours Read more...
Your Price
$54.25
  On Order
Ice Maker Bin Thermostat
★★★★★
★★★★★
(10)
PartSelect Number PS11740332
Manufacturer Part Number WP2313633
This is a bin thermostat made for standalone ice makers to activate the ice maker shut-off when bin is full. It senses how much ice is in the bin to determine if it should produce more ice or activate shut-off. The bin thermostat may need to be replaced if bin is overfilled, underfilled, or not producing ice. Thermistor can be tested with an ohm meter. This part is made of plastic and metal, and is white in color. This is an authentic part sourced from the original manufacturer.
Installation Instructions
Ray from Terry, MS
Ice maker overfilling with ice and would not stop production when full.
Very easy to replace. Down load the Manual online for a completely operating manual. Thermistor can be tested with an Ohm Meter. Proper values are listed in operating manual. Read more...
Your Price
$78.38
  In Stock
Recirculating Pump - 60Hz
★★★★★
★★★★★
(6)
PartSelect Number PS11740331
Manufacturer Part Number WP2313628
A recirculating pump is used with standalone ice cube makers. It circulates the water over the top of the evaporator plate, which produces a layer of ice that is then broken down into ice cubes. If you notice that your ice maker is no longer producing ice or there is no water flowing over the cooling plate, this could be due to the recirculating pump not working. Be sure to keep the pump clean and free of build-up. This pump is 5.75 inches in length, 4.75 inches in width, 4.25 inches in height and weighs 0.81 lbs. This is a genuine OEM appliance part that comes directly from the manufacturer.
Installation Instructions
Richard from North Wilkesboro, NC
was not making ice
diagnosed no water flow over evaporator checked voltage into pump then checked pump with ohm meter ordered pump and installed by removing access cover and water holding assembly installed new pump replaced water holding assembly and access cover and returned icemaker to service all is well Read more...
Your Price
$107.05
  In Stock
Icemaker Control Assembly
★★★★★
★★★★★
(16)
PartSelect Number PS2341896
Manufacturer Part Number W10190935
The “Icemaker Control Assembly” (Module & Motor Assembly, Ice Maker Control Module, Icemaker Module, Refrigerator Ice Maker Module) is what controls the actions of your ice maker. The control turns the timing cams and the ejector blades. It controls most of the basic parts and functions such as the heater, water inlet valve, the cube size, and cube ejection. If your ice maker control is broken it can no longer properly control the ice maker functions. It may not produce any ice, make small ice cubes, or have intermittent operation. This can occur due to normal wear and tear. The icemaker control assembly is attached to the ice maker mold, and is under the white cover. Test the icemaker control assembly by using a multimeter. If this reveals the assembly to be defective, you will need to replace this part. It is approximately 4.25 inches square, beige, and is constructed of plastic and metal. This replacement part features one icemaker control assembly, including the control module and the motor.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • Leaking
  • See more...
Installation Instructions
Daniel from Suwanee, GA
No ice
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. Read more...
Your Price
$133.97
  In Stock
Condenser Fan Motor
★★★★★
★★★★★
(5)
PartSelect Number PS11723170
Manufacturer Part Number W10822259
NOTE: As per the manufacture the part does not come threaded. A self tapping screw will need to be used to make threads.
Fixes these symptoms
  • Freezer section too warm
  • Fridge and Freezer are too warm
  • Fridge too warm
  • See more...
Installation Instructions
Nicholas from Frankfort, IN
Believed the condensor motor was defective and causing strange odor
First disconnected the quick release electrical connection. Then loosened the three screws that were holding the motor in the bracket. However, space is limited and even with small hands it was rather difficult as the screws were in there very tight. There are a few sharp edges on the bracket and in the surrounding area of the motor area, and nicked myself a couple of times. Removed the fan blade from the old motor and attached it the new motor with the old flat washer/screw. Reconnected the electrical connection and that was that. All-in-all an easy repair. Read more...
Your Price
$8.91
  In Stock
Compression Nut
★★★★★
★★★★★
(1)
PartSelect Number PS11743305
Manufacturer Part Number WP627018
The compression nut is used as a connection between the water supply line and other components in your refrigerator such as your ice maker and your water dispenser. Tools required for this repair include a pair of pliers and a socket set. Before installing this part you should take all perishable foods out of your refrigerator and store them somewhere cool, unplug the refrigerator from the power source, and shut off the water supply. This repair may require you to wear work gloves to protect your hands, and is considered an easy do-it-yourself fix.
Installation Instructions
harry from murfreesboro, TN
Water leaking from bottom of fridge
The line going from the ice maker fill valve ruptured and leaked water on the floor. The outlet fitting for the ice maker water inside the freezer was plugged with ice which caused the pressure to build up in the line and rupture it. The discharge tube inside was full of ice because the ice maker fill valve was old and was leaking ever so slightly. This allowed water to exit into the discharge tube gradually and build up ice to the point of blocking the discharge tube. Read more...
Your Price
$232.22
  In Stock
Circulation Pump with Motor
★★★★★
★★★★★
(3)
PartSelect Number PS11739740
Manufacturer Part Number WP2217220
The circulation pump assembly, used in a free-standing ice maker, delivers water from the water tank over the top of the evaporator plate. It does this to form the ice that drops onto the cutting grid. The first step in installing this part is to remove the chute, ice scoop bracket, water pan, and head cap screw that holds the plastic cover over the pump. Refer to the manufacturer-approved installation instructions for further guidance and accuracy. Make sure to disconnect and unplug the ice maker from the power source before installing the circulation pump. Remember to wear gloves to protect your hands.
Installation Instructions
Louis from Cheyenne, WY
Lack of frequent cleaning resulted in pump failure due to buildup from hard water mineral deposists
This ice maker is really a Kitchenaid appliance.

1. Remove all ice and drain water pan by removing drain cap.
2. Disconnect waterline and unplug ice maker
3. Set icemaker on a work bench unless you like working on your knees, head down.
4. Remove flip out chute and ice scoop bracket.
5. Remove water pan by removing thumb screws
6. Remove single 1/4" head cap screw that holds plastic cover over pump.
7. Remove discharge hose from pump. Pull clear plastic 1/8" diameter water supply line from notch in left edge of pump base.
8. Remove three cap screws holding pump. Two are visible. The third one is behind the pump and requires an 8" extension on the socket.
9. After the three screws are removed the pump drops down. The electric connection must be unplugged. Pinch the tabs on either side to release the plug.
10. Reverse procedure to install new pump. Unless you have really small hands or love being frustrated, don't bother to reinstall the third screw that is behind the pump. The pump stays in place just fine without that screw.
11. After reinstalling the icemaker, clean thoroughly by washing all inside surfaces with a strong bleach solution.
12. Run a cleaning cycle with one quart of strong bleach solution in the water tray. At the conclusion of the cleaning cycle, drain the water tray. Place unit into service. DON'T FORGET TO CLEAN REGULARLY. If the water supply is not chlorinated molds and algae will develop in recirculation hose.
Read more...

Appliance Type

Related Parts

Popular Whirlpool Ice Maker Models

Below are the most popular Whirlpool Ice Maker models we have. Enter your model number in the search box to find your model.