Tappan Range Parts

Tappan Appliance Parts

Popular Tappan Range Parts

Your Price
$47.59
   In Stock
Tappan Range Oven Bake Element
★★★★★
★★★★★
421 Reviews
PartSelect Number PS438018
Manufacturer Part Number 316075103
The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with this part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in. You may need a flashlight when making this repair.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Little to no heat when broiling
  • See more...
Installation Instructions
David from Shawnee, KS
Oven woudn't heat
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in.
Read more...
Your Price
$12.59
   In Stock
Tappan Range Drip Bowl - 8"
★★★★★
★★★★★
100 Reviews
PartSelect Number PS437595
Manufacturer Part Number 316048413
This chrome drip bowl is designed for use with electric cooktops and ranges. This drip bowl is sold individually. At the widest point this part has a diameter of approximately 10 inches. It sits beneath the surface burner element. It catches any drips or spills coming from the cookware on your burner. Because the cooktop is a high-traffic area of the kitchen, these bowls often get damaged, or get so dirty they can no longer be adequately cleaned. When replacing this part you need to remove the burner element. While you have it out we recommend inspecting the terminals and the element for any corrosion, arcing, or discoloration. Any of those things could be a sign of a bigger problem, and it indicates that the element and terminal block should be replaced.
Fixes these symptoms
Installation Instructions
John from Nisswa, MN
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones

I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Read more...
Your Price
$7.46
   In Stock
Tappan Range Chrome Drip Bowl - 6"
★★★★★
★★★★★
78 Reviews
PartSelect Number PS437596
Manufacturer Part Number 316048414
The drip bowl catches grease and spills that come from cooking on your stove top. They are located under the heating elements. Drip bowls are often neglected and can become rusted and cracked. If your drip bowl is damaged, it could allow grease, food, or other spills to drip inside your range. This could become a fire hazard. This 6 inch chrome drip bowl fits most electric ranges. Before you replace your damaged drip bowl, make sure the element is turned off and cool to the touch. To replace the drip bowl, remove the element, replace the current drip bowl, and reattach the element. This part is sold individually.
Fixes these symptoms
Installation Instructions
John from Nisswa, MN
Old pans/bowls were corroded
Very easy---simply unplug the burners, remove the old pans and replace with the new ones

I was extremely pleased with the easy ordering and prompt delivery of parts that actually fit as they should!
Read more...
Your Price
$43.86
   In Stock
Tappan Range Infinite Burner Switch
★★★★★
★★★★★
70 Reviews
PartSelect Number PS1145040
Manufacturer Part Number 316436001
The infinite burner switch controls the stove top eight-inch surface burner, which is the large surface element. If your surface element is not warming up, the element can be tested to determine whether or not it is defective. If your element is not defective, then it is more than likely that the infinite burner switch is the issue. Before you install the infinite burner switch you will need to unplug your range from the power supply, or shut off the home circuit breaker. The tools you will need to do this repair include a number one square head screwdriver and a pair of needle nose pliers.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when broiling
  • Oven is too hot
  • See more...
Installation Instructions
William from Burke, VA
Back Burner didn't function
We moved into our townhouse about 6 yrs ago. During the home inspection we checked the range and saw the Red light come on when we turned on each burner. After moving in we realized the large back burner did not work. The light came on but the element never got hot. I of course replaced the element but that did not work. Several years passed and we just ignored the issue. We just got by with 3 burners. Lately we realized how much easier it would be to have all four burners working. Knowing that we will be selling our townhome soon we figured we should either fix the problem or replace the range.

I didn't want to call a repair man because I didn't want to be charged a $150 to have him come out and they to pay extra for parts (and of course a 2nd visit). So I went to www.Partselect.com and typed in the model of my range. Found the diagrams for my range and saw that from the switch ran a pair of wires to a Universal Receptacle (aka Terminal Block Kit). I figured since the Red light turns on when I turn the switch on it has to be the Terminal Block.

I ordered the part from www.Partselect.com ($14.00 including shipping) and replaced the part. The burner still would not get hot. I decided to test the switch. I removed the Control Panel cover (which is secure by 2 screws just below the digital clock). Once the cover was off, I saw the Blue wires going from the switch to the Terminal Block. To test the switch, I disconnected the two Blue Wires from connectors H1 and H2 and temporarily connected them to H1 and H2 of another switch. Sure enough, when I turned the other switch the element got hot.

So I placed another order from www.Partselect.com for a replacement switch ($50 including shipping). When that part came, I flipped the electrical circuit going to the range. I then removed the Control Panel cover again. With the new switch in hand (holding it near the old switch still attached to the Control Panel, I used the pliers to pull out each wire from it's connector and place it to it's corresponding connector on the new switch. Once all the wires were connected to the new switch, I pulled the knob of the switch off then used a phillips screwdriver to remove the two screws holding the switch to the control panel. I replaced the old switch with the new one put the screws back in, replaced the knob. Turned the circuit back on and tested to make sure that the element got hot. When it did, then I replaced the Control Panel cover and enjoyed a nice dinner that was cooked in less time than we're accustomed to because of the new burner. So I spent a total of $64.00 to fix our range. Less than half the amount I would've spent if I called for a technican. And far less then buying a new range.

Partselect is a great resource for information. They have diagrams and schematics available to view and/or download. And when ordering it's a snap because there's an "Add to Cart" button next to each part it lists. So there's no confusion. I've already recommended Partselect.com to about 5 people. And will continue to do so!!
Read more...
Your Price
$16.24
   In Stock
Tappan Range Terminal Block Kit
★★★★★
★★★★★
37 Reviews
PartSelect Number PS470125
Manufacturer Part Number 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.
Fixes these symptoms
  • Element will not heat
  • Oven not heating evenly
  • Will Not Start
  • See more...
Installation Instructions
Steven from Taylors, SC
rental property stove only had 2 working burners and bottom drawer off track
first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place
Read more...
Your Price
$20.39
   In Stock
Tappan Range Surface Element - 8 Inch - 2600W
★★★★★
★★★★★
20 Reviews
PartSelect Number PS2339242
Manufacturer Part Number 316442301
The range surface element provides heat to the cooking surface on top of the range. The element has a universal plug, is 8 inches in diameter, spans 5 coils in width and reaches 2600 watts. Before you begin your repair, ensure that the elements are turned off and have had time to cool. Once you have removed the element this is a good time to ensure the terminal is in good condition (they can wear over time) which may need to be replaced as well. This quick repair requires no tools except gloves for safety, and a small amount of time.
Fixes these symptoms
Installation Instructions
David from Encinitas, CA
burner shorted out
I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner. Read more...
Your Price
$47.25
   In Stock
Tappan Range Temperature Sensor
★★★★★
★★★★★
45 Reviews
PartSelect Number PS1528542
Manufacturer Part Number 316490000
This genuine OEM oven probe is also known as an oven temperature sensor or range probe. This part is manufactured for a range, stove, or oven to detect the temperature within the oven cavity. The probe allows the oven to maintain the set temperature by sensing the temperature and sending the information to the ovens motherboard. You may need to replace this part if oven is not heating or is heating unevenly. Be sure to disconnect power to oven before replacing, as it is an electrical part. Tools needed are 1/4 inch nut driver and needle nose pliers.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
Tim from ASHAWAY, RI
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up. Read more...
Your Price
$35.86
   In Stock
Tappan Range Flat Style Oven Igniter
★★★★★
★★★★★
49 Reviews
PartSelect Number PS470129
Manufacturer Part Number 5303935066
This is a flat style oven igniter used to light the oven burner in a gas range. When the element in this igniter glows white hot, the gas is released from the safety valves, which lights the oven burner. If your range is not heating properly, or not heating at all, it might indicate a problem with this part. If the element in the igniter is only glowing red or orange, or not glowing at all, it will need to be replaced. This is a shorter style igniter. It is 3.72 inches in length, and it features an 18-inch wire lead. This kit includes the igniter, an instruction sheet, a mounting bracket, and the two ceramic wire nuts needed for installation. This part has an amperage range of 3.2 to 3.6. Unplug your appliance before you start any repair work.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Gas smell
  • See more...
Installation Instructions
John from Darlington, SC
Oven quit heating.
After reading up on the problem of the gas oven not lighting I decided I needed to install a new igniter. I had read where some people just pulled a panel off the back and installed a new one.. yeah, no such luck with this model so I had to crawl into the broiler drawer space [which I had to clean out first]. Note, if you wear trifocal glasses you might as well close your eyes and replace it by feel because there is no way to tilt your head back enough to see what you are doing and still get both arms and your chest in a broiler. Also be sure to remove all cats and dogs from the area before starting. They seem to think they can help or it's a game of hide and seek and they want to hide with you.. they were no help at all.
Other than that, it was quite easy.
Read more...
Your Price
$19.73
   In Stock
Tappan Range Light Bulb
★★★★★
★★★★★
11 Reviews
PartSelect Number PS12751166
Manufacturer Part Number 316538904
This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace with new light bulb. If the existing bulb is broken in the socket, disconnect the power to the refrigerator and use a pair of needle nose pliers to grip the internal fragments of the bulb to unscrew. Replace with the new bulb and reconnect the power to the refrigerator. These bulbs are sold individually and are a commonly replaced part; consider ordering a spare.
Installation Instructions
Colin from Hollis, NY
Ice-Maker and Water Dispenser not working.
First I disconnected the power cord, then removed the screws that held the bracket that holds the base for the water-filer in place. I then disconnected the water lines(intake and outflow). Next I removed the screws that held the water-filter's base in place. I then disconnected the release lock mechanism for the filter and finally removed the water-filter base. I did the reverse to install the new water-filter base. Previously I had tested the intake water line and noticed the water was flowing with enough pressure upto the water-filter's base but no water was exiting thru the outflow line, which leads to the Ice-Maker and Dispenser. I had tried changing the filter but that didn't solve the problem it was then I had realized that the Base was the problem. The actual problem was the spring-loaded valves for both the intake and outflow lines, which had a plastic prong that protrudes out of the base that is triggered by the filter when installed. The two prongs were worn-down so the filter wasn't activating the spring-loaded release valve to let the water thru. As for the light, I just unscrewed it. Read more...
Your Price
$22.73
   In Stock
Tappan Range PROBE
★★★★★
★★★★★
22 Reviews
PartSelect Number PS11731754
Manufacturer Part Number 316233903
Note: Connector could be different than original. If so cut & splice wires together with porcelain wire nuts.
Fixes these symptoms
  • Element will not heat
  • Gas igniter glows, but will not light
  • Little to no heat when baking
  • See more...
Installation Instructions
MaryLou from Monroe, NC
Range would not come on
Turned off power, took back off stove removed old probe.
I had to splice wires since new probe ends did not match up.
the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires.
After waiting, I turned the breaker on and my range came back on.
Read more...

Tappan Range Appliance Types

Related Tappan Range Parts

Popular Tappan Range Models

Below are the most popular Tappan Range models we have. Enter your model number in the search box to find your model.