Part Location Diagram of 316075103 Frigidaire Oven Bake Element
See part 5 in the diagram
Replacing your Frigidaire Range Oven Bake Element
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.com

Oven Bake Element 316075103

★★★★★
★★★★★
419 Reviews

Rated by 303 customers 

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.

$ 47.59
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS438018
Manufacturer Part Number 316075103
Manufactured by Frigidaire
Product Description

Oven Bake Element Specifications

The Oven Bake Element is a black, metal part which supplies heat to the oven. This element is 19-1/2" wide x 18-1/2" long and has 3-1/2" inserts. It is rated as "Easy" to install by users, and attaches to the bottom of the oven. If you notice visible damage, or that your oven is not receiving heat properly then it may be a problem with this part. Check your model number and user manual to see if this is the right part for you. It is important for you to disconnect your appliance from the power source before performing this repair. After disconnecting your appliance, remove the two screws/nuts connecting the old element, pull it out, and discard if faulty. Simply connect the new element prongs where the old element fit, and screw it back in. You may need a flashlight when making this repair.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Range Oven Bake Element

Replacing your Frigidaire Range Oven Bake Element
Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Element will not heat | Oven not heating evenly | Will Not Start
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Tappan, Kenmore, Crosley.
Part# 316075103 replaces these:
AP2125026, 09990062, 316075100, 316075102, 316075104, 316282600, 3203534, AP4356505, F83-455
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
419 Reviews
4.8
Filter By Rating:
  • 5 Stars
    354
  • 4 Stars
    47
  • 3 Stars
    8
  • 2 Stars
    4
  • 1 Star
    6
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
  • 3
Customer Repair Stories
 Average Repair Rating: 4.6 / 5.0, 303 reviews. What's this?
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing installation instruction that matched.
Electrical connection pulled off the element
When I pulled the element out of the back panel of the oven to remove it, the electrical connection got caught on the edge of the hole in the panel and disappeared back into the oven insulation. It was difficult to find and pull it back out to reinstall it on the new element.
Other Parts Used:
Broil Element Oven Bake Element
  • Carla S from WAYNESBURG, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My element had a hole in it
Removed old elements I stalled new ones
Other Parts Used:
Broil Element Oven Bake Element
  • Kathy from Gentry, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake Element Stopped Working
When I found the part I needed there was an instructional video on how to remove broken bake element and install new bake element. This was the best video short and sweet and anyone...I mean ANYONE could do it!

Step 1- cut off the power supply (I flipped by breaker, but you could just unplug the oven)
Step 2- remove baking racks
Step 3- unscrew the little metal plates inside the oven where the bake element meets the back of the oven (reserve screws for new element)
Step 4- carefully pull the bake element out until you have the wires through the holes
Step 5- carefully pull the bake element from the wire clips on both sides
Step 6- take broken element out of over and put new one in
Step 7- slide new bake element ends onto wire clips
Step 8- slide new bake element and connected wires back though back of oven
Step 9- used saved screws to screw metal plates on bake element to the back of the oven
Step 10- replace oven racks
Step 11- restore power to range
Step 12- enjoy a working oven and feel like an absolute PRO for fixing it yourself!!!!
  • Meaghan from HOLLY HILL, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Easy as could be
2 1/4 inch screws and 2 blade connectors fir the power. Took me longer to find my nutdriver than the repair.
  • Kenny from HENDERSONVLLE, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven heat element broke in 1/2.
Took screws out back of oven to get to connectors . Pulled old conectors off Installed new element took about 5 min. Very easy job. Also good time to clean oven .
  • Keith from LAKEVILLE, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element burned out.
Turned off power at the circuit box. After locating 1/4" nut driver (the hardest part of the repair)I removed the oven racks. Took the opportunity to wipe out oven. Removed the two screws holding the element in place.Pulled element out gently to expose the connections. Wiggled the terminal connector off the terminal on element. Gave the wire a little bend to keep it from pulling back into frame. Repeated process on other side. Removed new element from wrapper. Placed element on oven floor, reattached terminals--making sure they were on snuggly--carefully slid terminal ends back though slots in oven body. Lined up brackets, reinstalled screws, replaced racks and turned power back on. Turned oven on it worked. Made cookies! Very easy repair.
  • Pamela from FRIDLEY, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom burner wouldn’t heat
Watched the video
  • cynthia from SEBRING, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
element burnt out
purchased a square bit and removed screws easily and disconnected it from the wiring and pushed in the new element secured screw and it was back to baking.
  • Demoris from GOLDSBORO, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the old bake element was corroded and non-funtional
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
  • Stephen from RONAN, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element went out
The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. Pull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.
  • Nicholas from COTTONDALE, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

69 questions answered by our experts.
Sort by:
  • 1
  • 2
  • 3
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
William
January 2, 2019
I think it would be good to tell people to make sure the power is off
PartSelect logo
Hi William, thank you for contacting us. Yes, it is always best that before doing any repair you make sure your appliance is not connected to power so that you do not harm yourself or break something else on the appliance. Have a great day.

65 people found this helpful.

Was this helpful?
Thank you for voting!
Maureen
March 28, 2019
How to install heating element in bottom of oven?
For model number 79096010407
PartSelect logo
Hello Maureen, Thank you for the question. Here is a link to a How To video that may help. Good luck with the repair! https://www.youtube.com/watch?v=1E0VmuFtfXM

38 people found this helpful.

Was this helpful?
Thank you for voting!
Dustin
May 14, 2019
If my bottom heating element is broken can it cause the top part of the stove to not hear correctly
For model number TEF361GSB
PartSelect logo
Hello Dustin, thank you for your question. No, any oven issues shouldn't cause the top burners to be affected. The top burners are controlled by burner switches behind the temperature knobs and the oven control board and oven sensor control the oven elements and heating. I hope this helps.

19 people found this helpful.

Was this helpful?
Thank you for voting!
Ralph
May 22, 2019
Can you use the broil element for the bake element cause i don't use the broiler at al so would it work
For model number FEF326ABM
PartSelect logo
Hello Ralph, thank you for your question. Unfortunately, the broil element will not work for the bake element. To replace the bake element you would have to purchase PartSelect Number: PS438018. I hope this helps!

13 people found this helpful.

Was this helpful?
Thank you for voting!
Betty Justice
February 25, 2019
My bottom element heats fine. Since i purchased a new element some time back i have smut on my lower part of oven and on the element every time i cook something. I do not know what causes it. Will a new element help? Thank you.
For model number FEFL64FSD
PartSelect logo
Hello Betty, Thank you for contacting us. It is possible that the bake element is faulty. I suggest checking it with a multimeter. You should get a reading between 0-50 ohms. Good luck with your repair!

12 people found this helpful.

Was this helpful?
Thank you for voting!
Betty
February 6, 2019
Frigidaire oven element quick heating, so i know it needs to be replaced. My question is: Do i have the right model number to order a new one?
For model number FEF366EBE oven heat element
PartSelect logo
Hello Betty, Thank you for contacting us. After reviewing your model number I show PS438018 is the part number for the bake element for this model. Good luck with your repair!

9 people found this helpful.

Was this helpful?
Thank you for voting!
Vanessa
May 29, 2019
My oven has a new bottom element but it still won't heat up
PartSelect logo
Hello Vanessa, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

8 people found this helpful.

Was this helpful?
Thank you for voting!
Darlene
April 12, 2019
Does this part work with this model
For model number FEF352AWE
PartSelect logo
Hello Darlene, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS438018. Thank you for your inquiry, good luck with this repair!

8 people found this helpful.

Was this helpful?
Thank you for voting!
John
June 6, 2019
I need both top and bottom elements bottom element is 15 inches long
For model number vf91725643
PartSelect logo
Hello John, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. vf91725643 looks to be a serial number. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Amy
April 1, 2019
Will this particular element work
For model number FFEF3003NWA
PartSelect logo
Hello Amy, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS438018. Thank you for your inquiry, good luck with this repair!

6 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
Model Cross Reference
This part works with the following models:
PartSelect Number: PS438018
Manufacturer Part Number: 316075103
Brand
Model Number
Description
Frigidaire
00462048A
Range - Range
Frigidaire
00462048B
Range - Range
Frigidaire
00462048C
Range - Range
Frigidaire
00462048D
Range - Range
Frigidaire
20462052A
Range - Range
Frigidaire
20462052B
Range - Range
Frigidaire
20462052C
Range - Range
Tappan
30TESKWED-04-23
Range - Electric
Tappan
30TESKWED-23
Range - Electric
Tappan
30TESKWED-23-02
Range - Electric
Tappan
30TESKWED-23-03
Range - Electric
Tappan
30TESKWED1
Range - Electric
Tappan
30TESKWED2
Range - Electric
Tappan
30TESKWED3
Range - Electric
Tappan
30TESKWED4
Range - Electric
Tappan
31-1049-00-01
Range - Electric
Tappan
31-1049-00-02
Range - Electric
Tappan
31-1049-00-03
Range - Electric
Tappan
31-1049-00-04
Range - Electric
Tappan
31-1049-00-05
Range - Electric
Tappan
31-1049-00-06
Range - Electric
Tappan
31-1049-23-01
Range - Electric
Tappan
31-1049-23-02
Range - Electric
Tappan
31-1049-23-03
Range - Electric
Tappan
31-1049-23-04
Range - Electric
Tappan
31-1049-23-05
Range - Electric
Tappan
31-1049-23-06
Range - Electric
Tappan
31-2232-00-01
Range - Free Standing, Electric
Tappan
31-2232-00-02
Range - Free Standing, Electric
Tappan
31-2232-00-03
Range - Free Standing, Electric
Customer Service Representative

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service