- Home
- TBX25FPLLAD
- Instructions
TBX25FPLLAD General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
the ice dispenser quit working
7 of 19 people
found this instruction helpful.
-
Ronnie B from Hollister, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I opened the freezer door and removed the access panel, then with a phillip screwdriver,I removed 1 scew and used a pair of pliers to pull the wires off.I then reversed the prosess.EASY
Was this helpful?
Thank you for voting!
Light would stay on when door closed
3 of 7 people
found this instruction helpful.
-
James from Glendale Heights, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this helpful?
Thank you for voting!
family member melted fan with hair dryer
1 person
found this instruction helpful.
-
Lauraine from Rocky Hill, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Was this helpful?
Thank you for voting!
light switch freezer door
3 of 7 people
found this instruction helpful.
-
Sumlorq from Cleveland, OH
- Really Easy
- Less than 15 mins
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this helpful?
Thank you for voting!
Broken light switch
1 person
found this instruction helpful.
-
Deborah from BRADLEYVILLE, MO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person
found this instruction helpful.
-
Joe from SUGAR LAND, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d
... Read more
islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person
found this instruction helpful.
-
Loren from EL PASO, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back
... Read more
in SNAPP
Read less
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person
found this instruction helpful.
-
Gary from EAST JORDAN, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Bin of cubes was frozen over and I thought I had burned out the auger motor
1 person
found this instruction helpful.
-
Marianne from KANSAS CITY, KS
- Really Easy
- 15 - 30 mins
-
Wrench set
My friend easily installed the new motor but that wasn’t the problem it ended up being the control panel board on the fridge freezer door that is the problem. No one has that part #WR55X0058
That I need and I can’t find it on the internet they say because my fridge is almost 30 years old. I’ll keep searching. My fridge still works p ... Read more erfectly and makes cubes. They just won’t dispense. It’s my spare fridge and I’m not ready to get rid of it.
That I need and I can’t find it on the internet they say because my fridge is almost 30 years old. I’ll keep searching. My fridge still works p ... Read more erfectly and makes cubes. They just won’t dispense. It’s my spare fridge and I’m not ready to get rid of it.
Read less
Was this helpful?
Thank you for voting!
Evap fan failed, would need restarted by hand when weather warmed up
1 person
found this instruction helpful.
-
Linda from WILLIAMSPORT, PA
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Repair was super simple. Everything was a direct fit. Hardest part was unloading freezer to access evap motor. My freezer was old making my wire shields very brittle so I cut the shielding and used heat shrink tubing for a neat clean repair.
Was this helpful?
Thank you for voting!
Ice Crusher began to leave plastic in ice
1 person
found this instruction helpful.
-
Richard from BONAIRE, GA
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
We only needed the rear plastic cylindrical helix. After installing it, there was a squeal of metal on metal due to insufficient clearance between the rear moving blade and the Ice dispenser plate.
Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give ... Read more clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.
This was my first time at doing this so it took longer than someone experienced. But, it worked!
Refrigerator Ice Maker 7/16” (or ½” hole, stainless steel) washer just behind #334 Rear Moving dispenser Blade PS292310 to give ... Read more clearance so it doesn’t hit #345 / PS292441 Ice Dispenser Plate.
This was my first time at doing this so it took longer than someone experienced. But, it worked!
Read less
Was this helpful?
Thank you for voting!
motor was not working
4 of 10 people
found this instruction helpful.
-
Eleanore from Setauket, NY
- Easy
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Actually, a friend did it with me watching. He took out about 6 screws, removed the back plate and the old motor and installed the new motor when he realized the hole on the plate that goes in front of the motor was on the wrong side! This would have been a snap and done in about 30 minutes if it wasn't for the hole on the wrong sid
... Read more
e. So he drilled a hole on the correct side of the plate, using the old plate as a pattern, and it works fine!
Read less
Was this helpful?
Thank you for voting!
Fridge wasn't cooling and half freezing
1 person
found this instruction helpful.
-
Wendell Hayes from Dillob, SC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Part was perfect fit .Removed fan .three screws.replaced that s it
Was this helpful?
Thank you for voting!