- Home
- TBX25FPLLAD
- Instructions
TBX25FPLLAD General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fan would not turn when the refrigerator came on all the time. Would physically have to turn the fan blades.
2 of 2 people
found this instruction helpful.
-
David from CLIFTON, NJ
- Really Easy
- 30 - 60 mins
Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.
Was this helpful?
Thank you for voting!
Ice from icemaker taste metallic; new ice maker directly from box
2 of 3 people
found this instruction helpful.
-
Samuel from ALEXANDRIA, VA
- Difficult
- More than 2 hours
I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.
Was this helpful?
Thank you for voting!
Was Not Making Ice Or Getting Water
3 of 6 people
found this instruction helpful.
-
TERESA from COALMONT, TN
- Really Easy
- Less than 15 mins
-
Wrench (Adjustable)
Three easy steps, take off old part then all you do is tighten nut on one end of part and then just push other end of pipe down in slot. Did half to remove nut off the top end of tube very simple to do
Was this helpful?
Thank you for voting!
Ice Maker losing Ice out of bucket
2 of 3 people
found this instruction helpful.
-
Tina from Advance, NC
- Easy
- 15 - 30 mins
-
Screw drivers
I had to order bucket as well. Then I removed 3 screws from bottom of bucket and removed auger parts as a unit put new drive cup in new bucket and re attached auger parts as assyembly and reinstalled in freezer.
Was this helpful?
Thank you for voting!
Light would no longer turn on
3 of 6 people
found this instruction helpful.
-
paypal_shipping_address from Ripon, CA
- Really Easy
- Less than 15 mins
-
Pliers
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this helpful?
Thank you for voting!
Light out
2 of 3 people
found this instruction helpful.
-
Jodi from Benton Harbor, MI
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $
... Read more
120 service call.
Read less
Was this helpful?
Thank you for voting!
water overflowing in ice cube tray
2 of 3 people
found this instruction helpful.
-
Matthew from Sunland, CA
- Really Easy
- Less than 15 mins
Remove the rear cover, shut off the water, removed the hose, unplugged the electrical connector, removed the screw holding the valve on. Removed the plastic tube going into the freezer and reversed the steps
Was this helpful?
Thank you for voting!
Crushed Ice Only
2 of 3 people
found this instruction helpful.
-
Allen from Hills, IA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screw
... Read more
s that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.
Read less
Was this helpful?
Thank you for voting!
Ice Maker Did Not Work
2 of 3 people
found this instruction helpful.
-
Donald from Jacksonville, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Tried replacing water valve since no water in ice cube tray. Exact part not available due to age of refrigerator, but I got the equivalent replacement part for $18. Mounting holes different, but I made it work. Also one connect on new one slip connect whereas both compression fittings on old valve. I put it back together and icemaker no
... Read more
w works great.
Read less
Was this helpful?
Thank you for voting!
Original part cracked allowing crushing fingers to grab plastic guide jamming it.
1 person
found this instruction helpful.
-
Barry from SUN VALLEY, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts a
... Read more
s the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.
Read less
Was this helpful?
Thank you for voting!
Water valve failed. Constant drip in ice maker.
1 person
found this instruction helpful.
-
Steven from RUSHVILLE, IL
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
Removed old valve easily. New WR57XI0033 valve is designed to mount on lower left, but on mine it has to mount on lower right. Had to drill two 1/32 holes in lower rail to mount the new valve.
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
no water to icemaker
2 of 4 people
found this instruction helpful.
-
Bobby from Lewes, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
removed back cover--disconnect water supply-- removed screw holding vave and unplugged the
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
electric from the valve-- disconncect waterline to
the icemaker. reverse the to put on new part.
Was this helpful?
Thank you for voting!
leaking water from casket seal
1 person
found this instruction helpful.
-
Winston from BRONX, NY
- Really Easy
- 15 - 30 mins
Remove old gasket by pulling out one corner at a time and Installing it by placing it in the grove.
Was this helpful?
Thank you for voting!
Ice maker was leaking and causing the ice to freeze into a block.
1 person
found this instruction helpful.
-
Robert from SCARBOROUGH, ME
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
People would use the ice maker and just let it grind and eventually the bin and the plastic cup at the end of the auger broke.
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling ... Read more that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
I replaced the ice maker and once satisfied it worked and did not leak, I took the bucket/auger mechanism apart and replace both the bucket and the ice cup.
While the Frig is getting old, it has paneling ... Read more that matches our cabinets so we are trying to get a few more years out of this. This repair is one I should have done 10 years ago! Thanks Parts Select!
Read less
Was this helpful?
Thank you for voting!