EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TBX25FPLLAD General Electric Refrigerator - Instructions

All Instructions for the TBX25FPLLAD
106 - 120 of 203

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
water leaking from under dishwasher
1 person found this instruction helpful.
  • Edward from E LONGMEADOW, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.

Indeed , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.

A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this helpful?
Thank you for voting!
Ice Maker was not working
2 of 5 people found this instruction helpful.
  • FRANK M from EASTON, PA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes

Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people found this instruction helpful.
  • ED from ENON, OH
  • Very Easy
  • Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
Fan blade broken
2 of 5 people found this instruction helpful.
  • John from Cumberland, MD
  • Really Easy
  • Less than 15 mins
Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.
Was this helpful?
Thank you for voting!
Small Ice cubes/Jams
1 of 2 people found this instruction helpful.
  • Patricia from Port Republic, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set, Wrench set
My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people found this instruction helpful.
  • Stephanie from KEARNY, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
Worn out part.
1 of 2 people found this instruction helpful.
  • Theodore from Arlington, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed icemaker bin, removed auger assembly, cleaned broken part debris out, put in new part, re-assembled bin/auger assy, done!!
Was this helpful?
Thank you for voting!
valve wouldn't allow enough water to fill ice maker.
2 of 5 people found this instruction helpful.
  • james from Sanford, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people found this instruction helpful.
  • Ted from SANDWICH, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Only crushed ice. No cubed.
1 of 2 people found this instruction helpful.
  • JACOB from COLLEGEVILLE, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this helpful?
Thank you for voting!
Ice crusher did not work, Ice would plug in tub chute on discharge end.
2 of 5 people found this instruction helpful.
  • clayton from TUCSON, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Pulled ice tub, removed auger rotation motor and solenoid housing, removed solenoid and replaced with new one and reinstalled. Checked solenoid was working by holding freezer door open and closing switch to door an activating ice switch-- solenoid picked up. Put ice tub with auger back into freezer.
Was this helpful?
Thank you for voting!
Ice maker traydid not fill with water
1 of 2 people found this instruction helpful.
  • Willie from Virginia Beach, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.
Was this helpful?
Thank you for voting!
No water to icemaker
2 of 6 people found this instruction helpful.
  • Fred from Crawfordsville, IN
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks
Was this helpful?
Thank you for voting!
Ice maker only dispensed crushed ice.
1 of 3 people found this instruction helpful.
  • Richard from THE VILLAGES, FL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor /solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.
Was this helpful?
Thank you for voting!
socket had melted
1 of 3 people found this instruction helpful.
  • Chris from Charlotte, NC
  • Really Easy
  • Less than 15 mins
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this helpful?
Thank you for voting!
All Instructions for the TBX25FPLLAD
106 - 120 of 203