EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TBX25FPLLAD General Electric Refrigerator - Instructions

All Instructions for the TBX25FPLLAD
46 - 60 of 203

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker water valve failed open.
5 of 7 people found this instruction helpful.
  • O. V. from Virginia Beach, VA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set, Wrench set
The replacement single outlet water valve was not an exact replacement and required a slightly different mounting position. The original plastic hose to the ice maker attached to the valve with a plastic nut. The new connection requires only pushing the hose into a hole in the valve. Easy and simple. However, the new mounting angle prompt ly broke the brittle old plastic hose. I was able to pick the broken pieces of hose out of the valve with a fine point pick saving the new valve. If I hadn't been able to pick the broken pieces out of the new valve I would have had to order another one. Off to the big box store to buy new 1/4 inch plastic hose and a coupler. Repair completed and no leaks. If the hose hadn't broken, the I would have been done in 15 minutes. I suggest you plan to replace the entire plastic hose when you replace the valve.
Was this helpful?
Thank you for voting!
There was a warm spot at the front edge of dividing wall. The fan motor was not working.
4 of 4 people found this instruction helpful.
  • Kathrine from FORT MILL, SC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.
Was this helpful?
Thank you for voting!
cracked valve
6 of 11 people found this instruction helpful.
  • Don from Crete, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Super simple. Extremely fast delivery of part. Simply disconnect the 2 fast-on connectors to valve, disconnect intake and out lines. connect intake and out tubes to new unit, mount via screws to fridge, reconnect the 2 fast-on power connectors and your back in business. Could not be an easier repair.
Was this helpful?
Thank you for voting!
Ice maker stopped working.
5 of 8 people found this instruction helpful.
  • Alice from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Socket set
I first replaced the ice maker and when that didn't work, I found out through this forum that another possibility is the water outlet valve.

When I got the replacement, it took some time to install because the bracket wasn't the same as the original. There are enough places on the bracket to mount the unit, but it may requir e using some force to bend the bracket so that it will flush with the wall.

After installation, it took about 2 days to fill up the ice bin. It cycles out ice crescents every 2-3 hours.

Thanks partselect for having this forum and saving me some money by having others share their experiences.
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people found this instruction helpful.
  • Daniel from Crown Point, IN
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people found this instruction helpful.
  • James from Federal Way, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.
Was this helpful?
Thank you for voting!
Ice crusher not working
4 of 6 people found this instruction helpful.
  • Brian from Battle Ground, WA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Remove the ice maker, motor and replace.

The biggest problem was that the part was NOT available from GE. Part Select had the part, it was easily identified on their website and it couldn't have been easier to order it.

The repair from GE would have cost me hundreds of dollars. Thanks Parts Select.
Was this helpful?
Thank you for voting!
Ice Maker would not crush ice.
7 of 15 people found this instruction helpful.
  • Kelly from Canandaigua, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Removed tray from ref. Removed from cover from tray useing a screwdriver. Removed housing, took old parts out. Make sure you take the parts out in order and put new parts back in same order as old parts.
Was this helpful?
Thank you for voting!
Does not start , trips breaker
3 of 3 people found this instruction helpful.
  • Paul from RNCHO CORDOVA, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried the relay from compressor with small screwdriver, cut and replaced burnt wire going to relay,pushed new relay on compressor and wires unfortunately it did not fix the problem.
Was this helpful?
Thank you for voting!
broken outlet valve
5 of 9 people found this instruction helpful.
  • KEITH from WINDER, GA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
All the repair people was on the money . I read them all .1--- NO paper work with new valve (.no instructions) ..2--- bracket is not the same .. I reversed my braket and it worked fine .you do not have to bend bracket.3--- It will take a day or so to start making ice..4--- the plastic nut is no longer needed on the new type outlet valve . ...5--- the new outlet valve looks a little different from the old valve. WORKS GREAT ..
Was this helpful?
Thank you for voting!
Interior Light did not go on due to faulty switch
4 of 6 people found this instruction helpful.
  • Robert from Coto de Caza, CA
  • Really Easy
  • Less than 15 mins
I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people found this instruction helpful.
  • Lee from OZARK, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Was this helpful?
Thank you for voting!
switchlight on my refrigerator was not working
5 of 10 people found this instruction helpful.
  • Eileen from Coto de Caza, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this helpful?
Thank you for voting!
We found a snap ring and washer in a glass of ice
3 of 4 people found this instruction helpful.
  • Randy from Cohasset, AL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I took the ice maker tray out and dumped the ice and then removed 4 screws to take the plastic front off the drawer. I then took 4 more screws out to remove auger assembly. I could now unscrew the broken nut and replace it with the new one and put the snap ring and washer back in place and then put everything back together. Done
Had I had my lathe running at the time I would have made this part out of aluminum instead of the new one and original that is out of plastic which is why it did not last.
Was this helpful?
Thank you for voting!
Ice maker would only make very small and very few ice cubes.
3 of 5 people found this instruction helpful.
  • Margaret from Virginia Beach, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
After determining that the ice maker on this relatively new refrigerator would make ice cubes if it received the proper amount of water. Ordered the valve and received in a couple days. Using a nut driver, removed the cardboard cover from the back of the refrigerator. Removed one screw holding the valve bracket to the fridge and removed a nother screw holding the water supply line and the water line to the ice maker in place. Pulled plug on fridge and removed 2 wires from valve. Removed inlet and outlet lines from old valve and reversed the process installing the new valve.
Was this helpful?
Thank you for voting!
All Instructions for the TBX25FPLLAD
46 - 60 of 203