- Home
- TBX25FPLLAD
- Instructions
TBX25FPLLAD General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
ineffective frige door gasket due to stretching
8 of 10 people
found this instruction helpful.
-
Anita from Shawnee, OK
- Easy
- Less than 15 mins
I pulled off the old gasket and pressed in the new one. That's it!
Was this helpful?
Thank you for voting!
no water in ice maker
7 of 8 people
found this instruction helpful.
-
O.J. from SUFFOLK, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Change out water valve.. to find out my temp setting was to high. My kids changed the setting.. so my ice maker didnt work. The water valve will not open until it senses the right temp. Hope this help someone. But my part was here the next day
Was this helpful?
Thank you for voting!
mositure and tempature
8 of 11 people
found this instruction helpful.
-
Mark from Cheraw, SC
- Easy
- 30 - 60 mins
First the Kenmore refrigerator was listed as most parts as not available on the Sears web site.
The old gasket was split in several places and moisture and mildew was part of the clean up. Because of the cold weather at the time of shipment the note about using warm water to soften the gasket so it would be more pliable was extremely ... Read more helpful.
I was also reversing the door swing and found that it was not that hard , it took about 45 minutes and was done the 24ft frig is now working great
Thank
Mark
The old gasket was split in several places and moisture and mildew was part of the clean up. Because of the cold weather at the time of shipment the note about using warm water to soften the gasket so it would be more pliable was extremely ... Read more helpful.
I was also reversing the door swing and found that it was not that hard , it took about 45 minutes and was done the 24ft frig is now working great
Thank
Mark
Read less
Was this helpful?
Thank you for voting!
noise from condenser fan
10 of 17 people
found this instruction helpful.
-
donald from opelousas, LA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .
Was this helpful?
Thank you for voting!
rusty ice maker
7 of 9 people
found this instruction helpful.
-
Dean from Park Ridge, NJ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
removed old parts and installed new. went smooth
Was this helpful?
Thank you for voting!
stopped making ice
7 of 9 people
found this instruction helpful.
-
Timothy from Orange Park, FL
- Easy
- 15 - 30 mins
-
Nutdriver
First I turned off the water supply. Then I removed the ice bin and the ice maker by removing 4 screws and 3 electrical connections. This allowed access to the evaporator fan which was not moving. To remove the evap fan I removed two screws that hold the fan bracket. The fan assembly now had to be pushed back and rotated to remove fro
... Read more
m hole. There are 3 electrical connections that have to be disconnected from the fan, one ground wire that also is connected to the fan bracket and 2 power connections. Installing the new fan was the reverse of the above except the power connections were in a different location and i had to use the extension wires provided with the new fan to have the length needed to make the connection.
Read less
Was this helpful?
Thank you for voting!
broken fan blade in the freezer compartment
7 of 9 people
found this instruction helpful.
-
John from Cumberland, MD
- Really Easy
- Less than 15 mins
-
Pliers
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Was this helpful?
Thank you for voting!
compressor not starting
9 of 15 people
found this instruction helpful.
-
H.K. from Seagoville, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.
Certainly not PartSelect's fault. They have great service.
Was this helpful?
Thank you for voting!
no water to icemaker
6 of 7 people
found this instruction helpful.
-
Ron from Clinton, MO
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
turned off water supply, took screws out of bracket, then unhooked water lines. Installed water lines onto new valve, plugged it in then screwed bracket back onto fridge, turned on water and was back operating
Was this helpful?
Thank you for voting!
missing center cover slide for vegetable bins
6 of 8 people
found this instruction helpful.
-
Jean from Tucson, AZ
- Really Easy
- Less than 15 mins
I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks
Was this helpful?
Thank you for voting!
light not working
7 of 11 people
found this instruction helpful.
-
robert from FRANKLIN SQ, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
ice maker barely working
6 of 8 people
found this instruction helpful.
-
William from Provencal, LA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Repair was very simple. Removed refridgerator bottom back panel, about 6 or 7 screws. disconnected bad valve, installed new valve , connected water supply line and then reinstalled panel. Took about 15 minutes from start to finish.
Was this helpful?
Thank you for voting!
Drive cup broke due to ice cube jamming it
5 of 6 people
found this instruction helpful.
-
Bruce from Mobile, AL
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove three screws insert part; manually checked out drive and waited for ice to buildup and it worked like new.
Was this helpful?
Thank you for voting!
Wasn't Getting Any Water To The Icemaker
5 of 7 people
found this instruction helpful.
-
Mark from Ft. Lauderdale, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
It could not have been easier. The new part matched the old part exactly. I turned the water off going to the refrigerator, unscrewed one screw from the old part, pulled the electric plug loose, disconnect the copper water line from old part, cut off the black plastic tube next to the water valve going to the icemaker, and the new wat
... Read more
er valve was ready to install. It's that simple. I then took the new water valve, connected the copper water line to it, pushed the black plastic water line into its hole, connected the electric plug, and screwed the new part onto the refrigerater. In a matter of minutes I had water running to my icemaker again. I can't imagine the money I saved by doing this simple project myself. This took less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
Icemaker solenoid housing cracked
5 of 7 people
found this instruction helpful.
-
Mark from Bayside, NY
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The original piece was already removed. installation required a little custom fitting as the mounting was slightly different and the copper tubing from the water line needed to be bent to fit. The push in plastic connection (output to the icemaker itself ) was simple ( I was a little leary of it not leaking.)
I plugged in the solen ... Read more oid connection first
I attached both water lines and checked for fit. Made the adjustments and then screwed the bracket back on to the refrigerator. I could only install one screw but it holds it fine. I did have to trim the hard press board(cardboard) a little to fit the new valve. I believe the board is to protect against dust build up on the mechanical equipment (motor, condenser,etc)
I plugged in the solen ... Read more oid connection first
I attached both water lines and checked for fit. Made the adjustments and then screwed the bracket back on to the refrigerator. I could only install one screw but it holds it fine. I did have to trim the hard press board(cardboard) a little to fit the new valve. I believe the board is to protect against dust build up on the mechanical equipment (motor, condenser,etc)
Read less
Was this helpful?
Thank you for voting!