ALW2 - Instructions

Removed front panel.
Released 2 springs on belt tensioner.
Rolled drive belt off pulleys.
Unscrewed 4 bolts holding washer motor assembly.
Tilted motor to get at pump screws.
Removed 3 pump screws and pump slid right off shaft.
Aligned new pump and reinstalled screws.
Set motor assembly loosely in place. ... Read more
Rolled drive belt onto pulleys.
Re-attached tension springs.
Installed motor assembly bolts.
Re-installed front panel.

** I should have replaced drive belt at same time, but it is working with no leaks.

(UNPLUG APPLIANCE FIRST! )Used large flat bladed screwdriver to remove tub damper springs on front of tub.Then remomoved washer pump hoses after placing towel underneath to catch waste water.
Removed four bolts holding motor and pump assembly to tub pulled it forward slightly to remove motor electrical connector, turned assembly over ... Read more to remove pump ("torx bit")
Intalled new belt being mindful of routing and idler pulley. Seems new belt is slightly longer requiring a little tension spring adjustment might have to replace it also. Washer now functions properly!

I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and ... Read more added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com ... Read more then install other part taken off in oreder and make your wife very happy

After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was si ... Read more mple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

I followed the online line advise but I wait to add a few important notes. First, clean and use Loctite (blue works fine) on the four sheet mental screws holding the motor assembly to the internal frame. Next, mark the two capasator wire as they will have also to be removed. You probaby won't find the exact spin belt number on PartSeclect ... Read more 's site. By all means don't guess. Call the 1.888.895.1535 help number. They have all the cross-reference part numbers for the correct length belt.

Remove bottom and top front panel to access motor. Remove motor by loosening four bolts. Remove spring that applies pressure to the Idler pulley wheel. Pull out electrical connector by pressing on the tab on top. Remove rubber hoses by gripping clamps with pliers. Unhook belt from pulley at bottom of tub. Pull out motor. Push upward and i ... Read more nward the top of the tub to make pulling out the motor easier. Remove allen screws that secure the plastic pump housing so you can remove the belt. Replace belt. Remove retaining ring to replace Idler Pulley Wheel, remember to order replacement washers, mine was brittle and disintegrated so had to remove the second one from the bottom and used only one each side, seems to work fine. Reassemble everything in reverse order. It now purrs like a kitten, wife is now happy doing the laundry, I get to ride my motorcycle this weekend at the Los Angeles Crest Highway carving the canyons, whoohoo! Life is good.

it was really easy to gain access to the valve, but the part was just a little different then the original. I had to lengthen one wire to make the new valve work. This did take care of the problem when completed.

The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push t ... Read more he inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!

To replace the belt:
First, unplug the appliance. No sense in poking and getting zapped.
Remove any water from the tub, if there is some, by running the washer through the end of the rinse cycle. This is the point of extracting water through the water pump.
Remove the bottom, front access panel by taking out the two scr ... Read more ews at the bottom and sliding the panel down and out. It is held in place by metal clips at the top. So, it has to "unsnap" at the top.
Next, remove (by pulling out and up to disengage its hook) the left front stabilizer spring from the bottom of the outer tub. Pry it out with a screwdriver blade under the hook enough to release it from its hole in the frame. Once released, slide the hook along the lip of the frame towards the back of the washer and out of the way. Makes it easier to get back in if it is still stretched some. This allows it to be out of the way in order to remove the motor.
Disconnect the hoses attached to the discharge pump. Be sure to have a couple of towels handy for any water left in the lines. Place the towels directly under the hoses before disconnecting. Set the hoses to the side of the washer cabinet.
Loosen and remove the back (when looking at the motor from the front access) two bolts holding the motor support frame to the frame supporting the transmission.
Next, locate and remove the top two bolts holding the motor frame to the tub frame. Be sure to support the motor as the last bolt is removed so that it does not fall down.
Tilt the motor slightly to the left. Locate the wiring harness at the top left side of the motor. There is a plastic clip in the middle and on top of the wiring harness. Push down on the clip as you grasp the harness. This will release the clip's grip at the back of the harness and allow you to pull it out. Set the harness back behind one of the nearby tension springs to keep it out of the way.
Once the harness and bolts are removed, tilt the bottom of the motor towards you and pull down and out to clear the outer tub frame.
With the motor out, fiip it over and locate the three screws holding the pump in place. Using a #25 torx head screwdriver, remove the screws. The pump will now separate from motor. Visually check that the pump does not have an obstruction. Manual check by spinning the pump by hand. It should move freely.
Before installing the spin belt, clean the motor pulley of any residue.
Remove and replace the idler arm spring. Leave the spring attached to the arm only. Do not reattach it to its anchor point on the motor frame.
Install the spin belt, making sure that the belt is on either side of the pump's rear leg. (Rear leg being the leg 90 degrees counterclockwise to the pump outlet port.) Be sure that the idler arm pulley is able to apply pressure to the belt.
Reverse steps to put the pump, motor and springs back in place. Be sure to plug in the wiring harness before the motor is place back into position.
Tip: Leave the idler spring off until after the spin pulley is wound onto the helix pulley. You can reach around the motor from the right side and grasp the pulley. Spinning it slowly as you feed the belt will make it easier to get it back on.
Last, plug in the machine and give a Tim Allen ARH, ARH, ARH, Ugh?

if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i cal ... Read more led and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

Biggest trick is getting the agitator off. It seems like it is bolted on. I used a piece of braided cotton cord to run under both sides of the agitator and just pulled real hard. It WILL pop off.

Next the old seal will also seem to be attached. The edge is firm but not bolted. A small prybar will help.

Easy repa ... Read more ir to do, but it did not fix my problem. I decided to get a new washer rather than go through further disassembly.

Place black rubber adapter on the end of the drain hose and stick in the stand pipe drain. That's all.