ALW2 - Instructions

First push inner tub to left rear, all the way, and
unscrew hinge from inside of tub. repeat same on
right side. lift cover off and unscrew other half of
hinge off cover, both sides.reverse procedures and your done.
Note: always replace both hinge's new while
you have it apart.

Brake pad kit does not come with installation instructions even though it says it does. Remove bottom front panel from washer. There are three brake pads. One of mine (the right one) broke into three pieces and was found on the bottom of the washer. This is how I identified what was wrong. Run the washing machine on the handwash extr ... Read more a light cycle (you could use another cycle, I used this one because I believe it is the shortest), there is a point in the cycle where the disk clamping the brake pads separates from the brake pads and allows you to remove and replace the pads. During other parts of the cycle, the disk is clamped onto the brakes and you could not remove or install a brake pad. I removed the two black hose on the bottom right to get to the right brake pad. Have a 2 gallon bucket ready to collect the water if you did run the washer as above. With difficulty, I was also able to reach around the back side of the right brake pad. I used a socket wrench set. I then removed and replaced the left brake pad. I left the rear brake pad in place. I was not able to get to it.

My washing machine was severely off balance during the spin cycle. It would bang violently against the side and “walk” across the laundry room. I was able to fix this for under $25 dollars of parts from partselect.com and a few hours. I rated the task as easy, but I am somewhat mechanically inclined. Others may find it a bit difficult but ... Read more I believe anyone except an absolute beginner can do this job.

Fix this problem before significant damage is done to your base! Otherwise the job will take more time and be a LOT more expensive. My base had experienced a little damage but thankfully it did not require replacement. When the snubber wears out, it allows the tub to rub against the base. Metal on metal is never a good thing.

Also I chose to replace the springs, even though it may not have been 100% necessary. You have to take them off anyway and they are inexpensive. It is easy to know when a spring is broken, but not as easy to know when it has lost some of its spring. Just makes sense to me to replace them.

I used the directions below which I found on the internet. They are listed below unedited by me. I have added a few of my own comments below that.

• Remove power and all hoses
• Lift top by inserting putty knife just inside front clips to release
• Remove front and rear panels, 10mm
• Disconnect drain hose from bottom of drum, pliers - spring clip
• Remove 6 springs from bottom of drum using channel lock or spring tool
• Lay on side, remove drive belt by turning large drive pulley and side tension to belt
• Remove water level hose on side of drum, pliers - spring clip
• Remove drum from cabinet by sliding out top. It is not necessary to remove drum from transmission.
• Inspect base plate for damage
• Lay drum on padded surface, upside down
• Remove C clip, drive pulley, being careful to observe order of parts and washers
• Loosen 6 screws holding down old snubber. DO NOT REMOVE SCREWS, THERE IS A VERY STRONG SPRING UNDER THIS PLATE. Loosen screws only enough to get old snubber out.
• Clean dust from area.
• Insert new snubber, keeping it even while tightening screws.
• Reverse other processes above to assemble washer. Replace any broken drum springs. Replace belt if worn.

My tips:

• After you remove the tub you will see a lot of fine white dust in the bottom of the washer. That is from your old worn out snubber. Vaccum it out.

• I didn’t have a spring tool but I found that using a pair of vice grips to remove and replace the springs was easier than using channel locks.

• Technically, I believe the clip is actually called an e-clip. If you have the correct tool for this removing and replacing it will be a lot easier. I did not have the tool. I used an open end wrench that was just the right size to butt up against the two ends of the clip. A light tap with a hammer against the other end of the wrench and it popped right off. I used a pair of needle nose pliers to put it back on.

• Also regarding putting the e-clip back on, at first I could not see the groove that the clip was supposed to slid into. It was below the little plastic piece with the teeth. I used a small flat screw driver inserted into the groove to gently pry it up and had someone gently tap on the plastic piece which pushed it down enough to expose the grove.

• I highly recommend heeding the warning regarding the loosening of the 6 screws holding the snubber. I did not have any trouble with this but there is a 200 lbs spring underneath that you do not want to release. It could injure you and might be hard to put back. Just loosen each screw 1/4 turn at a time until the snubber can be removed.

That's about it. I took me about 4 hours

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!

To replace the pump and belt for the Maytag washer, you really need remove the springs and suspended the tubs. I needed help to pull the 2 springs out (high tension) with a big plier. I removed the 3 bolts that held the motor to the frame and flipped it out to the side to expose the 3 long screws that attached the pump to the motor. Th ... Read more e pump was easily removed and replaced with the Philip screw driver. I preset the belt between the pump and the rotor before sliding the motor back in place. After botling the motor back into the frame and carefully pull and snap the spring back into the holes, I routed the belt around the pulley and turned it into the groove. This took some time to get it on properly as it is pretty tight. Once the cover was replaced, the washer worked as expected.

The washer is four years old.
This is the second time I needed to replace this same drain hose on this same washer since I had the machine
There is only my wife ant myself maybe, 2 -3 medium size loads per week - why I would have two drain lines develop the same problem in almost the same location in two years is disconcerting ... Read more
There must be a design problem with the clear plastic hose - Suggest Maytag go to a thick walled rubber hose
The hole is alway inside the washer on the bottom just after the hose bracket - I suspect that something rubbing causing a small pin hole to develop - when the condition first starts it is very difficult to located -There will be water under the washer
Run the washer and discharge the water - to locate

The replacement must be made through the lower front removable panel - and is easier to do if the pump return hose is also disconnected from the pump

Be very carful with the thin wall replacement hose - very light weight plastic - do not pull across the floor of washer - it could easily get damaged

Your company did a get job getting the part to me - The Fed Ex track system was great
I could tell exactly where the delivery was al all times -

After pulling the machine away from the wall and turning off the water and unpluging. I simply removed the panel in the back and reached underneath and removed the belt. Took off the hose clamps and removed the three screws holding the pump on. Put the new pump back in place and hooked up the hoses. Then put the belt on for a test ru ... Read more n.......all OK put the back on and was done. Whole job about twenty minutes. Saved over two hundred dollars doing this myself. Very simple repair.

just took the front off and then took the old motor off and switched over about 2 parts from the old to the new and then put the new part on and then placed the front back on and it was ready to go

Removed the waterlines. Set the ends in a small pan or bucket to catch the water.Do the same with the drain line.
Keep an old towell handy as water will drain out of the drain pump when you remove the drain hose. Removed the back panel. Use a flat bladed screw driver to pop the top off the two clips in front holding the top down. Lif ... Read more t the top and pull the two screws which holds the front in place. Remove the front and set aside. Underneath, use gloves and the screw driver to remove the six springs by placing the screwdriver through the top hook end about an inch and with both hands lift the spring off. Carefull not to let the blade slip off and bust your knuckles on something,hence the gloves. Lean the machine over and walk the belt off the pulley. Disconnect the small tube in the back left corner from the drum and lift the unit out from the top. Set the drum on it's top and loosen the six screws under the big pulley just enough to pull the snubber out. Replace new snubber, tighten screws. Set drum back in place and reattach springs. Lean unit over and replace belt. Reconnect the small tube, back left corner. Replace the front panel and top. Connect the drain line and replace the rear panel. Connect waterlines and check for leaks. I went ahead and replaced all springs. I recommend replacing the belt while your at it. I'm wishing I would have. It runs like new, gets more water out on the spin cycle and the dryer dosn't take as long to dry the clothes.

Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need t ... Read more o be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

First I took the front shield off, then I took the motor off.

I suggest if you are replacing the pump, order the belt at the same time, you must remove the pump to replace the belt.

Following on-line instructions for the dis-assembly. Replaced bearing and seals for outer drum bearing and cleaned and lubed assembly.

Not only very loud at spin cycle, but started to leak water as well. Pulled lower front panel off and ran a load of clothes while laying on the floor with flashlight watching. Sure enough, water spraying out from outer tub bearing area.
Remove top front panel, sides and top, disconnect hoses and unplug wires at top of control panel, ... Read more there is a plug in there. Now you should just have base unit and tub exposed so you have plenty of room to work. Next joy is to remove agitator. This is where my fun began. After removing fabric softner dispenser from top of agitator, I could not see bolt holding it on. There was a long plastic rod sticking up which looked like part of the agitator itself, so went online to a repairmans site and they said simply pull that rod out and bolt will be under it. Paid 24 bucks to them and still could not remove rod, ended up going thru slots in side of agitator with a small chisel and cutting it off, then took a 3/4" hole saw and drilled hole in top of agitator, its only about 1/8" thick and what do you know, THERE is the bolt!!!!!!! Removed bolt and out comes agitator. Next, remove cap from outer tub, take 4 bolts out of inner tub, remove inner tub. Next, remove plastic nut from shaft, I tried this with channelocks and could not budge it, ended up splitting nut with chisel and slightly damaged threads on shaft which I cleaned up easily with 60 degree thread file. Be very careful if you use this method. You can use channelocks to reinstall, just clamp on the unfinned part of nut.Take out the lint filter and throw in garbage, do not reinstall!!!!!! That filter is part of the reason tub bearing goes out!! Next, remove aluminum hub from shaft, mine was already loose so was easy. If yours is tight, screw in one of the old inner tub bolts almost all the way in and use hammer and punch to loosen. You can do the same for new one. Next, remove 6 bolts from outer tub and pull outer tub off shaft.Flip outer tub upside down and gently pry bearing out, mine came out easy as was spinning inside tub bearing fit. After cleaning everything I used Scotchseal 800 industrial sealant because bearing fit was loose. I made a clamp out of 1x2 wood and a long 1/4" bolt to hold bearing in tub to prevent it from pushing out, sometimes the sealant will cause this to happen, then I let it setup for 24 hours. Put it all back together, no leaks and SUPER quiet. Be sure and check your bottom bearing too while you have it all torn down, mine was fine. Do not forget to change O ring on spline shaft before reinstalling agitator. As far as the hole I drilled in agitator, just tapped it 1/2" pipe and screwed in a plastic pipe plug. You will need an extension and a 5/8" 12 point socket to do this.

Pulled motor, as the belt will not come off unless you take to water pump off off the motor. Installed new idler wheel, washers, clips and belt. Reinstalled motor.
Works good and hopefully lasts a long time!