ALW2 - Instructions

By sliding the machine out away from the wall I tipped it back so that it set against the wall on an angle enough for me to work on the bottom. I removed the belt and drive pully. The brake stator can be removed from the bottom if drum is centered. The brake is under pressure from a big spring in there that applies the brake. Replacing th ... Read more ree of its mounting screws with longer ones (10-24 x 2) allows you to let pressure off of the brake spring slowly. Replaced brake rotor and stator and compressed spring with long screws as in removal. Replaced all original screws to hold in place. Installed pulley and belt. Works like brand new, all for about $30. I bought the snubber also but did not realize that this is not part of the brake. I little confusing on the parts drawing.

I took pictures at different steps in case I forgot how it was assembled. Unplugged the power, turned off the water hoses, unplugged the hoses, pulled the washer out, took of the access panel in the lower left hand corner, took of two tec screws that hold the water valve in place, removed the four wires that were attached to the water va ... Read more lve, removed the water hose attached to the water valve, reattached everything to the new water valve. The only difficulty is the access panel is a bit small

I first unplugged the washer. I removed the 2 screws that hold the front panel and removed the front panel, they are located at the very bottom outer edges of the front panel.
I then removed 4 of the large springs that are attached to the drum, this washer has six but I only removed the front 4. Removed the two hoses going to the wat ... Read more er pump and drain hose, removed 4 bolts that attach the motor to its mounting bracket. Unplugged the wiring harnesses going to motor and what looks like a capacitor mounted to the side of the motor.Then I removed the drive belt. ( when the machine would first start to spin it would make a clacking noise which ended up being a chunk out the the drive belt causing the belt tenshioner to slap causing that noise and letting the drum spin during the wash cycle. So far very easy. I then removed the motor and when it is disconnected you can then remove the water pump. Three hex head bolts need to be removed and it pulls right off. I then removed the six bolts that hold the brake pads in place. I applied silicone grease to the new brake pads and installed them. The pad at the back of the drum was very hard to line up with the holes. I used a very small screwdriver to line up the disc brake mounting holes to get the bolts started and it worked fine. I then put it all back together and it works great. I have to add that I have been an auto mechanic for 28 years and not to brag but this is not your average repair job.

to replace the seals is the easier part of the job. I Removed the front panels and removed the front screws for the top and opened up. Then you have to remove the agitator, then the bell plug, the bolt holding the bell along with the bell, then the 1-1/2" nut under that. then slide the plastic washer that fits into the splne. to remove th ... Read more e drum you have to remove the plastic top to the drum assembly. Then you can remove the drum along with the along with the alumunum splined hud that is atrtached the the metal drum. Before removing the drum the seal under the plastic washer mentioned above needs to be removed. once the drum is out you can in bolt the aluminum splined hub from the metal drum. The outer plastic drum has a seal that is glued and slides over the vertical flange. The glue is not included in the kit. once the botom seal is installed. install the new aluminum splined hub to the metal drum. install lower seal to botom of the splined hub. reinstall the hub. once the large nut and plastic spined washer is installed. The top seal neds to tapped onto the hub agian with an object that matches the dia. of the seal flange. the n install the bell, nut ans plug. The bell does not like to align to the splined shaft, do not force it. reinstall the agitor an assemble the rest.

Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged i ... Read more n. Clamps are to big for application but do work. So far so good!

took off 2 bolts
on front panel (at the bottom). removed the spring tentioner.
next i spun the belt around until it came off
the pullies.
Then i removed 4 bolts holding the (pump and motor) spun this around to expose the pump screws(4) Took off the pump and did the same inreverse order except i put a new belt on also ... Read more ...
Good LUCK!!!

Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the sp ... Read more ring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.

Remove the electrical power plug and disconnect the water hoses at the back. Remove the lower front panel by taking out the two screws at the bottom edge. Then lift out the upper front panel which exposes the two sheet metal screws holding down the top panel. Lift open the top panel and secure it up about 90 degrees so it doesn't flop ove ... Read more r backwards. Twine tied to something overhead works fine. Replacement procedure for the valve is obvious, once exposed.

I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub ... Read more repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.

As the other posting said, it appears our problem was due to constant overloading, as an inspection of the machine with the bottom service panel removed clearly revealed all three milkstool legs broken away from the round center piece. My teen-agers are now aware that I am somewhat displeased about this.
My first action was to order ... Read more the repair manual. In retrospect, it was only marginally useful as a job aid, but was essential in verifying ID of the part and understanding details of how the machine works. I started by following the manual which said to remove the agitator. The agitiator didn't want to be removed, even after repeated attempts and applications of varying amounts of both physical and vocal persuasion. So, I reconsidered what I really needed to be doing, and dislodging the agitator (and subsequently all of the spline seals) really wasn't necessary. I just needed to get to and replace the crushed milkstool (and leave everything with a seal alone!).
So, Phase 1 - I removed the front panels, and tilted up the top. I then disconnected the power cable to the motor and the inlet/outlet hoses to the pump (more on my haste in this step in a moment...). The wiring harness is held in place on the machine back and milkstool by plastic retainers that release when compressed. I then disconnected the green ground wire, the panel that holds the blue water inlet valve assembly, the black hose on top of the tub and the clear air pressure hose (just pulls straight out of the tub side connector). This allowed the top to be removed and set aside. I then pulled the drain hose through and pulled the plate that holds it in place from the back, then removed all the screws that hold the cabinet to the base, then set the cabinet aside. Next, I disconnected all 7 springs from the base to the tub, and the tub was free. I pulled the tub from the base (not too heavy) and inverted it to get at the motor/pump/milkstool.
Phase 2 - gently removed the idler spring and removed the belt from the pulley. Pulled 10 1/2" self-tapping screws that hold the milkstool to the tub and the motor to the milkstool (these can be discarded as you get new ones with the milkstool). Now pulled 6 screws that hold the brake pads in place, and pulled the brakepads. The manual says to replace the pads whenever pulled, but these didn't look terribly worn, and work just fine after reassembly. The pulley then came off easily, and then subsequently so did the milkstool (with integrated bearing). Reassembly was the reverse of disassembly, and all seemed logical enough until I got to reattaching the hoses to the pump. The manual does not make it clear which one goes where, and I forgot to take a picture of that part of the machine before dismantling. Long story short, I put them on backwards, and you'll probably not be surprised to hear the machine didn't work as anticipated when we turned it on! (wouldn't spin, wouldn't pump out the water and made a nice puddle in the laundry room). Once we ladled out all of the water from the tub and reversed the hoses, everything worked fine. So - words to the wise (1) mark hoses, wires, etc with tape, grease pencil, whatever works for you BEFORE disassembly and (2) take close-up digital pics as you progress.

Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orien ... Read more tation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

I tilted machine onto the front to acces the rear panel. i removed the three screws to expose pump, took of the drive belt located under appliance, removed the three pump screws and removed old defective pump. I installed new pump, put the drive belt back on, reinstalled back panel and screws, hooked the appliance up and started. Been run ... Read more ning great ever since. Entire process too about 10 min.

I removed the front cover to gain access to the motor. I saw that the belt was starting to get chewed up so I removed it. While looking at the schematic on Parts.com I noticed the Idler Pulley Wheel was much larger then one currently on the machine. I ordered that also in case I needed it. I needed it. Once I replaced the belt and th ... Read more e pulley the machine ran better then ever. Originally I thought I just needed the belt but thanks to Parts.com I realized I needed a little more. Thanks.

First remove the bottom front access door. The helix drive nut and pulley were both chewed up. I pushed the pulley up into the brake assembly to make sure it released properly. Mine released and the drum spun freely (I had my 8 yr old assistant turn the drum first). The helix nut turned with the drum so I assumed the transmission was good ... Read more to go. Once my drive nut and pulley came in (two days), [UNPLUG WASHER AND DISCONNECT WATER] I took the top front cover off and lifted the top up and back on it's hinges. Next I disconnected the motor wiring harness, the bleach tube, the fill hose, the six drum springs, and the drain hose from the pump. Pulled the drum out of the shell and flipped it upside down. I took off the helix drive nut and removed the 8 bolts that hold the "milk stool and bearing assembly" and motor to the drum, also 2 screws that go into the plastic reservoir. I raised the milk stool enough to get the pulley out. (Belt was good) Put in new pulley and pushed the milk stool back down. (I was careful to keep the bearing on the shaft splines). Put the belt back on the pulley and idler. Put in all the bolts and put back together in reverse order. I recommend starting with the back drum springs, that's how I did it and it was easy. About an hour. Good luck.