EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3968 - Instructions

All Instructions for the 3968
91 - 105 of 178

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Varying heat
0 of 1 people found this instruction helpful.
  • Kimbel from Rhoadesville, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.
Was this helpful?
Thank you for voting!
light bulb went out in my oven
2 of 7 people found this instruction helpful.
  • Janet from Ada, MI
  • Really Easy
  • Less than 15 mins
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this helpful?
Thank you for voting!
oven light burnt out
3 of 10 people found this instruction helpful.
  • William from Schwenksville, PA
  • Easy
  • Less than 15 mins
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this helpful?
Thank you for voting!
Oven temperature all over the place
0 of 1 people found this instruction helpful.
  • Paul from Plaistow, NH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven th at held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.
Was this helpful?
Thank you for voting!
Getting codes and beeping
1 of 4 people found this instruction helpful.
  • Arthur from Dallas, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.
Was this helpful?
Thank you for voting!
Light burned out in upper oven
0 of 1 people found this instruction helpful.
  • Shirley from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Screwed in light bulb and glass protector
Was this helpful?
Thank you for voting!
replaced oven lightbulb
0 of 1 people found this instruction helpful.
  • peggy ann from forest city, NC
  • Really Easy
  • Less than 15 mins
very easy
Was this helpful?
Thank you for voting!
Oven would not turn on and get hot.
0 of 1 people found this instruction helpful.
  • Tom from Altus, OK
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found yo ur web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.
Was this helpful?
Thank you for voting!
Oven temperature lagging set temperature by almost 100F
0 of 1 people found this instruction helpful.
  • William from Edgewood, WA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fi xed the problem, so I just ordered the more expensive control board -- hope that does it.
Was this helpful?
Thank you for voting!
Oven would not work
0 of 2 people found this instruction helpful.
  • george from San Antonio, TX
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench set
Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Broken plastic knob
  • Judy from McKinney, TX
  • Really Easy
  • Less than 15 mins
Placed new knob directly on post. No problem
Was this helpful?
Thank you for voting!
Fan runs continually ,door locked,error code f2,f3,f7
  • John from Dacula, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with m atched harness /.connection, installed 2 screws ,turned on breaker.
Was this helpful?
Thank you for voting!
Had code F1 and F3 on my oven. Oven wouldn't heat.
  • Cindy from Polson, MT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Watched the video and it was as easy as described. Not many things go as easily as this.
Was this helpful?
Thank you for voting!
change oven sensor
  • Lloyd from Eau Claire, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Followed provided video
Was this helpful?
Thank you for voting!
All Instructions for the 3968
91 - 105 of 178