3968 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not turn on
-
Stacey from Tampa, FL
- Easy
- Less than 15 mins
-
Screw drivers
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.
Was this helpful?
Thank you for voting!
Oven would overheat
-
MARK from roseville, MN
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this helpful?
Thank you for voting!
Oven have F2 and F3 codes following cleaning cycle making oven inoperable
-
Timothy from Longmeadow, MA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!
Other Parts Used:
Was this helpful?
Thank you for voting!
oven not staying on. fault cod F-3 showing
-
James from Cumberland, MD
- Really Easy
- 30 - 60 mins
-
Screw drivers
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.
Was this helpful?
Thank you for voting!
Front burner would not heat properly.
-
Michael from Milton, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.
Was this helpful?
Thank you for voting!
Lower left Surface Element burnt
-
John from Nashville, TN
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange.
... Read more
3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.
Read less
Was this helpful?
Thank you for voting!
burned out switch
-
KENNETH from DEEP RUN, NC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
killed power...removed back of stove...removed switch and replaced it..reinstalled back...powered up
Was this helpful?
Thank you for voting!
leg was bent, also metal receiving bracket bent
-
Virginia from Oceanside, CA
- Really Easy
- 30 - 60 mins
-
Wrench (Adjustable)
Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adju
... Read more
st front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.
Read less
Was this helpful?
Thank you for voting!
Original burner stopped heating up
-
John from Nesconset, NY
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.
Was this helpful?
Thank you for voting!
Top oven sensor
-
Alan from Bonita, CA
- Easy
- 30 - 60 mins
-
Screw drivers
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires to
... Read more
gather. The oven cooks fine, I have not tried the cleaning cycle yet.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat on Back Cycle
-
Jeff from Thousand Oaks, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resi
... Read more
stance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
-
Claude from Lakewood, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)
Was this helpful?
Thank you for voting!
Temp spikes.
-
Wayne from Grantsburg, WI
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.
Was this helpful?
Thank you for voting!
surface burner failure
-
Gerald from Hot Springs Village, AR
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.
Was this helpful?
Thank you for voting!
Range had an F-2 code on the control panel
-
Greg from Frederick, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou
Was this helpful?
Thank you for voting!