EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3968 - Instructions

All Instructions for the 3968
61 - 75 of 178

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven Temperature was 50 degrees low
2 of 3 people found this instruction helpful.
  • Eugene from Clinton, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person found this instruction helpful.
  • William from Nashville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
Was this helpful?
Thank you for voting!
Replaced Burned-out Cooktop Element
1 person found this instruction helpful.
  • Seth from Old Orchard Beach, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten sion wire for one that would not reach with the new configuration and everything works perfectly.
Was this helpful?
Thank you for voting!
lens light was broken and missing.
1 person found this instruction helpful.
  • Allan from Rolla, MO
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop < br />and turned electrical power on.
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person found this instruction helpful.
  • Dolores from Edmond, OK
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Was this helpful?
Thank you for voting!
Right rear burner under glass no longer would heat
1 person found this instruction helpful.
  • John from Maple Valley, WA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person found this instruction helpful.
  • Larry from SOLON, IA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Small burner on glass top stove stopped working.
1 person found this instruction helpful.
  • REX from VIRGINIA BEACH, VA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don 't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person found this instruction helpful.
  • Louis Rodriguez from Granbury, TX
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people found this instruction helpful.
  • Robert from Funston, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person found this instruction helpful.
  • Pat from PAYSON, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person found this instruction helpful.
  • John from Arvada, CO
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person found this instruction helpful.
  • tommy from FAYETTEVILLE, NC
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person found this instruction helpful.
  • Dennis from AIKEN, SC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done
Was this helpful?
Thank you for voting!
My original back leg broke because the floor is uneven. Had to pull it out several times.
1 person found this instruction helpful.
  • Phyllis from BROWNVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this helpful?
Thank you for voting!
All Instructions for the 3968
61 - 75 of 178