EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3968 - Instructions

All Instructions for the 3968
76 - 90 of 178

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the broiler drawer guides broke
1 person found this instruction helpful.
  • Jeri from NEW RICHMOND, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers
All I had to do was pull the drawer out and screw on the new part! Awesome experience...and it was so easy to find the part on the website, everything is very clear and with pictures to ensure where the part belongs...who could ask for more?
Was this helpful?
Thank you for voting!
Top oven element works, but bottom element works only intermittently
2 of 5 people found this instruction helpful.
  • Bruce from Glencoe, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
Was this helpful?
Thank you for voting!
Terminal block arc'ed because a wire had become loose.
1 of 2 people found this instruction helpful.
  • Larry from Scranton, KS
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All ch ecked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this helpful?
Thank you for voting!
After doing an oven self clean cycle, oven temp couldnt be set correctly, heat element was warm,not hot
1 of 2 people found this instruction helpful.
  • Philip from Winter Haven, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After trying to set the bake temp after the self cleaning, it would not heat up. I Googled the model number,selected your link because it mentioned my symptom,and said usually it is the temp sensor in the oven that gets damaged by the high self cleaning heat. Your site had a place to enter my model number. You provided a great exploded vi ew of the parts, showing me my sensor,then you provided the part number of the kit i needed,and filled out the order form with payment method. Less than a week later I got my part with instructions. Your video showed me the two screws I remove from the front ,and I pulled the old part out and uplugged it's connector. Replacement was easy, and oven was fixed! Thank you for a great site! You held my hand through it all!
Was this helpful?
Thank you for voting!
broiler drawer hung crooked on one side.
1 of 2 people found this instruction helpful.
  • Denise from Festus, MO
  • Easy
  • Less than 15 mins
  • Screw drivers
I can't believe how easy this was to fix! I amazingly found the part on-line at PartSelect website. I love that you pick part by size, color, etc. I didn't have a part or model number, so this made it super easy! I ordered the part and got it in the mail within 2 days....YEAH! I got my screwdriver out and attached the peice, slid the drawer back in and shazam! it was fixed! Thank you PartSelect and kudos to the person that set up the way you order your parts......awesome! Thanks!
Was this helpful?
Thank you for voting!
One of the broiler drawer support broke
1 of 2 people found this instruction helpful.
  • Jay from Charleston, SC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.
Was this helpful?
Thank you for voting!
Oven not heating to desired temp
2 of 5 people found this instruction helpful.
  • Raymond from Ridgecrest, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab le adapter that came with the new sensor was needed in my case.
Was this helpful?
Thank you for voting!
Oven would not heat
1 of 2 people found this instruction helpful.
  • Ralph from Nicholasville, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and ove n works like new.
Was this helpful?
Thank you for voting!
Oven Over Heating
1 of 2 people found this instruction helpful.
  • Steve from New Albany, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Was this helpful?
Thank you for voting!
F1-1 and F3-1 error code
2 of 5 people found this instruction helpful.
  • Barbara from Lakeville, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...
Was this helpful?
Thank you for voting!
element or temperature sensor failed: not working
1 of 3 people found this instruction helpful.
  • David from Mary Esther, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
The broiler drawer support broke while removing the drawer for cleaning. Order part through Part-Select, arrived within 4 days, replaced broken part same day.
1 of 3 people found this instruction helpful.
  • Stanley from Brunswick, OH
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.
Was this helpful?
Thank you for voting!
broiler drawer supports broken
1 of 3 people found this instruction helpful.
  • Clarence from Yorktown, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
removed drawer from track replaced supports on track and one on the drawer.
Was this helpful?
Thank you for voting!
not heating/kicking oven off
0 of 1 people found this instruction helpful.
  • Kevin from Virginia, IL
  • Easy
  • Less than 15 mins
  • Screw drivers
Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well
Was this helpful?
Thank you for voting!
All Instructions for the 3968
76 - 90 of 178