38FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 people
found this instruction helpful.
-
judy from palatine, IL
- Really Easy
- 15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people
found this instruction helpful.
-
Georgene from Rock City, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit
... Read more
e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Read less
Was this helpful?
Thank you for voting!
Replace the oven Sensor
3 of 5 people
found this instruction helpful.
-
Michael from Exeter, NH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo
... Read more
k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Mike
Read less
Was this helpful?
Thank you for voting!
the burner element stopped working
2 of 2 people
found this instruction helpful.
-
Dominic from Fleetwood, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
Unscrewed ceramic stove top , lifted top and exposed element , unscrewed element from top and disconnected wireing (marking wires to assure proper reinstillation .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ... Read more ement .
Replaced top on stove and rescrewed to secure .
Read less
Was this helpful?
Thank you for voting!
The Broiler element split after oven self-cleaning
2 of 2 people
found this instruction helpful.
-
Rolland from New Port Richey, FL
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the pr ... Read more ice of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the pr ... Read more ice of the element plus the cost for the service call.
Read less
Was this helpful?
Thank you for voting!
Inside was missing
2 of 2 people
found this instruction helpful.
-
maria from MANTECA, CA
- Really Easy
- 30 - 60 mins
Great I can bake now
Was this helpful?
Thank you for voting!
f1&f3 error> continuous beeping,oven stopped working after using the self cleaning mode
2 of 2 people
found this instruction helpful.
-
Robert from FITCHBURG, MA
- Easy
- 30 - 60 mins
-
Nutdriver
I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people
found this instruction helpful.
-
FRANK from CLARENCE CTR, NY
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas
... Read more
ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Drip pans were not original to range, I could not get them clean.
2 of 2 people
found this instruction helpful.
-
Lynn from BRADENTON, FL
- Really Easy
- Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people
found this instruction helpful.
-
richard from SAINT MARYS, KS
- Very Easy
- Less than 15 mins
-
Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people
found this instruction helpful.
-
Frances from Summerfield, FL
- Really Easy
- Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people
found this instruction helpful.
-
francis from mount holley, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor.
... Read more
That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Read less
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people
found this instruction helpful.
-
phillip from Farmington, NM
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose
... Read more
by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Read less
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people
found this instruction helpful.
-
Daniel from MOUNT HEALTHY, OH
- Very Easy
- Less than 15 mins
-
Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!