EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FN Magic Chef Range - Instructions

All Instructions for the 38FN
106 - 120 of 363

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Used part
2 of 3 people found this instruction helpful.
  • Sabrina from FREMONT, CA
  • Very Easy
  • Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this helpful?
Thank you for voting!
front burner would not heat
2 of 3 people found this instruction helpful.
  • Jack A from Biloxi, MS
  • Really Easy
  • Less than 15 mins
  • Socket set
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people found this instruction helpful.
  • Rhoda P. from Secaucus, NJ
  • Really Easy
  • Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people found this instruction helpful.
  • Max from Houston, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way. Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people found this instruction helpful.
  • Richard C from San Jose, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.

* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.

* Unscrew the cartridge top from the cartridg e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.

* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.

* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.

* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.

* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.

* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people found this instruction helpful.
  • Peter from Westcliffe, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people found this instruction helpful.
  • OSCAR from BRISTOL, CT
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people found this instruction helpful.
  • jeff from haskell, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug ged it into the harness in the back and reinstalled oven in the cabinet.
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people found this instruction helpful.
  • Eugene from Clinton, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this helpful?
Thank you for voting!
lamp retainer gasket disintegrated when changed burned out bulb
2 of 3 people found this instruction helpful.
  • Sandra from Flemington, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people found this instruction helpful.
  • Phillip from Reston, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person found this instruction helpful.
  • Michael from Thornton, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people found this instruction helpful.
  • Ben from Belen, NM
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
Replaced Burned-out Cooktop Element
1 person found this instruction helpful.
  • Seth from Old Orchard Beach, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten sion wire for one that would not reach with the new configuration and everything works perfectly.
Was this helpful?
Thank you for voting!
replace element
1 person found this instruction helpful.
  • alex from huntington, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
All Instructions for the 38FN
106 - 120 of 363