38FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip bowls were burned and tacky
473 of 483 people
found this instruction helpful.
-
Donna from Dallas, TX
- Really Easy
- Less than 15 mins
First I removed the old bowls and replaced them with the new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drip bowls needed to be replaced
455 of 546 people
found this instruction helpful.
-
John from Chester, VT
- Really Easy
- Less than 15 mins
took old bowls out, put new bowls in, took a coffee break
Other Parts Used:
Was this helpful?
Thank you for voting!
Stove top element not working due to bad receptacle.
196 of 216 people
found this instruction helpful.
-
Richard from Carthage, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister ... Read more 's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
My sister ... Read more 's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Read less
Was this helpful?
Thank you for voting!
F1 code - gas over would not heat.
172 of 188 people
found this instruction helpful.
-
george from birmingham, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Replacing ... Read more the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.
Read less
Was this helpful?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
163 of 215 people
found this instruction helpful.
-
David from Westford, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening,
... Read more
reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Read less
Was this helpful?
Thank you for voting!
Old drip pans stained
218 of 427 people
found this instruction helpful.
-
Linda from Atlanta, GA
- Really Easy
- Less than 15 mins
Replaced old drip pans with new ones - very easy - even a 68 yr old lady can do it!!
Other Parts Used:
Was this helpful?
Thank you for voting!
one of my burners would only work half the time, and you had to wobble it to make it work
138 of 265 people
found this instruction helpful.
-
cindy from Sebeka, MN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected the new element using the wire caps, and finished bye rescrewing the element backinto place.
Other Parts Used:
Was this helpful?
Thank you for voting!
We needed new drip pans and no one carried the model we needed
67 of 71 people
found this instruction helpful.
-
sylvia from ventnor city, NJ
- Really Easy
- Less than 15 mins
we removed the old pans after first removing the electric heating element and simply inserted tne new pans
Other Parts Used:
Was this helpful?
Thank you for voting!
F1-1 code
79 of 110 people
found this instruction helpful.
-
charles from marstons mills, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Fa
... Read more
ilure to do so will cause the plastic plug connector to melt from oven heat.
Read less
Was this helpful?
Thank you for voting!
Burned terminal block and filter board
95 of 208 people
found this instruction helpful.
-
Joseph from Decatur, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench set
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.
Was this helpful?
Thank you for voting!
Repeated oven temperature sensor fault codes.
35 of 43 people
found this instruction helpful.
-
David from Arlington, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the righ
... Read more
t side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.
Read less
Was this helpful?
Thank you for voting!
replaced heating element on flat surface stove top
35 of 48 people
found this instruction helpful.
-
dennis from assonet, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.
Was this helpful?
Thank you for voting!
Oven would not heat- Beeped nonstop and flashed F3
29 of 33 people
found this instruction helpful.
-
Erin from Greenwich, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voi
... Read more
la!! The oven turned on and now it works like new!!!
Read less
Was this helpful?
Thank you for voting!
Inner Oven Glass broken
29 of 42 people
found this instruction helpful.
-
David from Wayne, NJ
- Easy
- 30 - 60 mins
-
Screw drivers
I removed two retainer screws which released the outside panel.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the rep ... Read more acement glass assembly back together.
Next I removed 2 screws which hold the middle glass pane from one of its retainer brackets.
The was another panel with 4 screws to remove before reaching the final glass inner assembly.
Once that panel was reoved with the broken glass it was time to put the rep ... Read more acement glass assembly back together.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven wouldn't heat the right temperature (you would have to add 100 degrees on to it)
26 of 36 people
found this instruction helpful.
-
Claudine from Bethlehem, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.
Was this helpful?
Thank you for voting!