38FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Front left burner quit after bright flash under glass top
11 of 19 people
found this instruction helpful.
-
Brian L. from Wilkes-Barre, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I ohmed out the burner element that wasnt working and found it was open. I ordered a new element thru PartSelect and installed it in the stove. I powered up the stove and turned on the burner but it didnt get hot. After a bit of testing I found that the new elements safety overtemp terminals werent in the same configuration as the origina
... Read more
l unit. I made some wiring adjustments and the burner was operating properly. Thanks PartSelect
Read less
Was this helpful?
Thank you for voting!
Oven temperature lower then setpoint.
7 of 8 people
found this instruction helpful.
-
Robert from Massapequa, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove
... Read more
and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
Read less
Was this helpful?
Thank you for voting!
oven temperature not reaching setting/temp. up and down
7 of 8 people
found this instruction helpful.
-
Ellen from Schenectady, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
Was this helpful?
Thank you for voting!
Door Spring Broke
7 of 9 people
found this instruction helpful.
-
Thomas from Van Nuys, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
The F3 error code displayed and beeped during use of the oven and oven shut down.
7 of 9 people
found this instruction helpful.
-
Debra from Colts Neck, NJ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who
... Read more
added their comments! They gave us courage to give it a try.
Read less
Was this helpful?
Thank you for voting!
my oven would not heat to proper temp
6 of 6 people
found this instruction helpful.
-
mark from CHAMBERLAIN, SD
- Very Easy
- Less than 15 mins
-
Screw drivers
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. T
... Read more
his repair took about 10 mins and the oven works perfectly. Thanks !
Read less
Was this helpful?
Thank you for voting!
F3 code, oven wouldn't heat.
8 of 12 people
found this instruction helpful.
-
Shaun from Kimball, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by re
... Read more
moving the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!
Read less
Was this helpful?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
7 of 9 people
found this instruction helpful.
-
Peter from FREDERICK, MD
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ... Read more ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.
Sincerely
Peter from Maryland
Read less
Was this helpful?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
6 of 7 people
found this instruction helpful.
-
Janet from Philadelphia, PA
- Really Easy
- Less than 15 mins
replaced drip pans with correct type
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven would not heat consistently
6 of 7 people
found this instruction helpful.
-
Leland from Orting, WA
- Easy
- 30 - 60 mins
-
Screw drivers
I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of
... Read more
the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !
Read less
Was this helpful?
Thank you for voting!
replace light in oven
5 of 5 people
found this instruction helpful.
-
william from aiken, SC
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.
Was this helpful?
Thank you for voting!
the left front burner burned out & none of the lights to show if a burner was hot would come on.
5 of 5 people
found this instruction helpful.
-
Richard from Fair oaks Ranch, TX
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
FIrst we found the power source ( this took us awhile) and cut the power at the fuse box. then we unplugged the cooktop and started to take out screws. It turned out the screw removal had nothing to do with the stove top coming out. We took the taping knife & pried it under a corner and lifted. the cook top was just sitting on the count
... Read more
er.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
The hardest part of the whole job was holding the cook top because we did not disconnect the downdraft fan other than to pull the tape off the vent & fan. Now we could undo the rachet screws that held the glass top to the cook top & remove it.
Theburner was simply a matter of pulling connections loose & placing them on to the new one. The clips that hold the burner in place were removed w/ a screwdriver & replaced on to the new burner. Watch for the numbers on the burner underside to know where to reattache the clips. the unit that lights up to show that a burner is hot would not come off, but we managed to remove
the plastic part even though the clip screw would not loosen, and since it only had to float near by we used the unused wire included in the new part to hold it in place. Putting the unit back together was not too hard, but it took us a little while to get it all lined up. Be carefull of what ever you work on, the downdraft fan scratched up the counter top that we were working on. we started with cardboard under it & should have continued, we did not want to try & remove the fan. Then we put it back in the counter opening & plugged everything back in & to our amazement ( we are not handy people) it worked! the lights that had refused to work when one unit was burned out now worked on all four units. thank you partselect, we were able to do the repair with what you sent.
Read less
Was this helpful?
Thank you for voting!
no temp control
21 of 53 people
found this instruction helpful.
-
Cathreen from Lusby, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
very easy
Was this helpful?
Thank you for voting!
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
5 of 5 people
found this instruction helpful.
-
Aubrey from EADS, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!