38FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
spring broke on one side of door hinge
14 of 20 people
found this instruction helpful.
-
Travis from Lexington, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.
Was this helpful?
Thank you for voting!
Burner was out but the burner coil worked on onother burner
10 of 10 people
found this instruction helpful.
-
Richard from Orange, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Was this helpful?
Thank you for voting!
oven getting 50 degrees or more, hotter than setting
10 of 10 people
found this instruction helpful.
-
Joseph from Wappingers Falls, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.
Was this helpful?
Thank you for voting!
After self cleaning the oven received an error code telling me the sensor was bad.
11 of 13 people
found this instruction helpful.
-
Christine from Davie, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working corre
... Read more
ctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )
Read less
Was this helpful?
Thank you for voting!
Baked on sauce
12 of 16 people
found this instruction helpful.
-
Julie from Newnan, GA
- A Bit Difficult
- More than 2 hours
Used cooktop creme, oven cleaner and Mr. Clean sponges. After many days of working on the surface, we were able to remove 99% of the sauce.
Was this helpful?
Thank you for voting!
F1 code and oven wouldn't operate
11 of 15 people
found this instruction helpful.
-
Robbie from Hillsboro, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on ... Read more . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on ... Read more . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.
Read less
Was this helpful?
Thank you for voting!
Burner not working
12 of 18 people
found this instruction helpful.
-
Warren C from Slidell, LA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First thing- I cut off power to the range. I then removed two screws to allow the cook top to be lifted. I marked the wiring and replaced the burner. Reapplied power and started cooking!
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people
found this instruction helpful.
-
Mark from Lake Orion, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
Oven would not preheat and gave 'F1' error
9 of 11 people
found this instruction helpful.
-
Joshua from Reno, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
Was this helpful?
Thank you for voting!
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
9 of 11 people
found this instruction helpful.
-
Crystal from Scott City, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now ju
... Read more
st like a new oven.
Read less
Was this helpful?
Thank you for voting!
1998 oven unit flashing F3
10 of 14 people
found this instruction helpful.
-
chris from houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people
found this instruction helpful.
-
Raymond from BLOOMINGTON, MN
- Very Easy
- Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
burner receptacle burned out
8 of 9 people
found this instruction helpful.
-
Michael from N. Haverhill, NH
- Easy
- 15 - 30 mins
-
Screw drivers
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Was this helpful?
Thank you for voting!
Broiler unit would only heat on one side
8 of 9 people
found this instruction helpful.
-
Lawrence from Morganton, NC
- Really Easy
- 1- 2 hours
-
Screw drivers
Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.
Was this helpful?
Thank you for voting!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
7 of 7 people
found this instruction helpful.
-
Jared from UNION GROVE, AL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the ... Read more wire to my oven plug at the terminal block.
I removed the whole back panel and everything else seemed OK visually.
1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.
2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.
3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Read less
Was this helpful?
Thank you for voting!