38FN Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
"F3" error message and no oven heat
1 person
found this instruction helpful.
-
Pat from PAYSON, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and
... Read more
behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Read less
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person
found this instruction helpful.
-
Dennis from AIKEN, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall
... Read more
screws and turn Circuit breaker power back on. Done and Done
Read less
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person
found this instruction helpful.
-
Marvin from DECATUR, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor
... Read more
back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Read less
Was this helpful?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
1 person
found this instruction helpful.
-
BETH from COUNCE, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person
found this instruction helpful.
-
Helen from SPRINGFIELD, OH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem
... Read more
as to what to do. The unit is working great now.
Read less
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person
found this instruction helpful.
-
Paul from SEATTLE, WA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to
... Read more
new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Read less
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person
found this instruction helpful.
-
Dolores from Edmond, OK
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi
... Read more
sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Read less
Was this helpful?
Thank you for voting!
Burnt out
2 of 4 people
found this instruction helpful.
-
David from Elba, AL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or ... Read more it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or ... Read more it will not come on.
Read less
Was this helpful?
Thank you for voting!
Right rear burner under glass no longer would heat
1 person
found this instruction helpful.
-
John from Maple Valley, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off ... Read more
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off ... Read more
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Read less
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person
found this instruction helpful.
-
Bruce from SOUTHBURY, CT
- Really Easy
- 30 - 60 mins
-
Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
burner would not heat.
1 person
found this instruction helpful.
-
Jackie from Hughes Springs, TX
- Really Easy
- Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people
found this instruction helpful.
-
Tawnia from SHOW LOW, AZ
- Really Easy
- Less than 15 mins
take out the old put in the new
Other Parts Used:
Was this helpful?
Thank you for voting!