38FK Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Burnt out
2 of 4 people
found this instruction helpful.
-
David from Elba, AL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or ... Read more it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or ... Read more it will not come on.
Read less
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person
found this instruction helpful.
-
Helen from SPRINGFIELD, OH
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem
... Read more
as to what to do. The unit is working great now.
Read less
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person
found this instruction helpful.
-
Paul from SEATTLE, WA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to
... Read more
new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Read less
Was this helpful?
Thank you for voting!
Right rear burner under glass no longer would heat
1 person
found this instruction helpful.
-
John from Maple Valley, WA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off ... Read more
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off ... Read more
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place
Read less
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person
found this instruction helpful.
-
Dolores from Edmond, OK
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi
... Read more
sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Read less
Was this helpful?
Thank you for voting!
replace element
1 person
found this instruction helpful.
-
alex from huntington, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Replaced Burned-out Cooktop Element
1 person
found this instruction helpful.
-
Seth from Old Orchard Beach, ME
- Easy
- 15 - 30 mins
-
Nutdriver
Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten
... Read more
sion wire for one that would not reach with the new configuration and everything works perfectly.
Read less
Was this helpful?
Thank you for voting!
Element burned out, broke circle, heat only half
1 person
found this instruction helpful.
-
Michael from Thornton, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering
... Read more
the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Read less
Was this helpful?
Thank you for voting!
The oven did not heat, but the top burners worked fine.
1 person
found this instruction helpful.
-
Marvin from DECATUR, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor
... Read more
back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.
Read less
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person
found this instruction helpful.
-
Pat from PAYSON, AZ
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and
... Read more
behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Read less
Was this helpful?
Thank you for voting!
Element burn out. Would not heat
1 person
found this instruction helpful.
-
Dennis from AIKEN, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall
... Read more
screws and turn Circuit breaker power back on. Done and Done
Read less
Was this helpful?
Thank you for voting!
Oven would not hold temperature, not turn on, and would shut off during use.
1 person
found this instruction helpful.
-
John from Arvada, CO
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili
... Read more
ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Read less
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person
found this instruction helpful.
-
tommy from FAYETTEVILLE, NC
- Very Easy
- Less than 15 mins
-
Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people
found this instruction helpful.
-
Robert from Funston, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!