EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FK Magic Chef Range - Instructions

All Instructions for the 38FK
76 - 90 of 237

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people found this instruction helpful.
  • richard from SAINT MARYS, KS
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Had an F2 message go off then F3 when I tried to turn the stove on
2 of 3 people found this instruction helpful.
  • Daniel from MOUNT HEALTHY, OH
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!
Was this helpful?
Thank you for voting!
front burner would not heat
2 of 3 people found this instruction helpful.
  • Jack A from Biloxi, MS
  • Really Easy
  • Less than 15 mins
  • Socket set
simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people found this instruction helpful.
  • Phillip from Reston, VA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
lamp retainer gasket disintegrated when changed burned out bulb
2 of 3 people found this instruction helpful.
  • Sandra from Flemington, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people found this instruction helpful.
  • Eugene from Clinton, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people found this instruction helpful.
  • OSCAR from BRISTOL, CT
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.

The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
F 3 signal on display pad every time oven warmed up
2 of 3 people found this instruction helpful.
  • jeff from haskell, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plug ged it into the harness in the back and reinstalled oven in the cabinet.
Was this helpful?
Thank you for voting!
Oven did not heat up in bake mode.
2 of 3 people found this instruction helpful.
  • Peter from Westcliffe, CO
  • Easy
  • 30 - 60 mins
  • Screw drivers
The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people found this instruction helpful.
  • Max from Houston, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way. Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Was this helpful?
Thank you for voting!
Small burner on glass top stove stopped working.
1 person found this instruction helpful.
  • REX from VIRGINIA BEACH, VA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don 't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person found this instruction helpful.
  • Louis Rodriguez from Granbury, TX
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person found this instruction helpful.
  • William from Nashville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!
Was this helpful?
Thank you for voting!
Oven shutting off, getting an F1 error on ECM
2 of 4 people found this instruction helpful.
  • Ben from Belen, NM
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.
Was this helpful?
Thank you for voting!
All Instructions for the 38FK
76 - 90 of 237