EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FK Magic Chef Range - Instructions

All Instructions for the 38FK
61 - 75 of 237

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
One of the electric stove top elements had burnt out
4 of 5 people found this instruction helpful.
  • Anthony from Palmyra, VA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.
Was this helpful?
Thank you for voting!
Uneven Heating/ High Heat Broiler To No Heat
3 of 3 people found this instruction helpful.
  • Jack from Houston, TX
  • Difficult
  • More than 2 hours
  • Screw drivers
After replacing heating element then selector switch, I came to think the only other thing was the thermostat. It finally worked. . . But not without some tribulations. This note is for a repair involving thermostat for a w130 jenn-air or maytag wall oven, do not follow instructions included with replacement part! It says the br and ba terminals are to be reversed with this replacement part. . . Not so! After re-connecting (as per instructions) nothing worked! If you have this model jennair or maytag, my suggestion is to replace the wires to connections just as they were removed from the old one. I finally did this after much frustration and electrical testing with a multimeter. Hope this note helps someone. Good luck!
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people found this instruction helpful.
  • Daniel from Prescott, MI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people found this instruction helpful.
  • Dave from SANTA BARBARA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Was this helpful?
Thank you for voting!
Crazy codes and not heating the oven properly at desired temp settings
3 of 3 people found this instruction helpful.
  • Stan from CHICAGO RIDGE, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. I f you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people found this instruction helpful.
  • sherri from elk horn, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Was this helpful?
Thank you for voting!
Temp out of wack
3 of 4 people found this instruction helpful.
  • Peter from Montello, WI
  • Really Easy
  • More than 2 hours
  • Nutdriver
replaced heat sensor
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people found this instruction helpful.
  • phillip from Farmington, NM
  • Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Was this helpful?
Thank you for voting!
f1&f3 error> continuous beeping,oven stopped working after using the self cleaning mode
2 of 2 people found this instruction helpful.
  • Robert from FITCHBURG, MA
  • Easy
  • 30 - 60 mins
  • Nutdriver
I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.
Was this helpful?
Thank you for voting!
The Broiler element split after oven self-cleaning
2 of 2 people found this instruction helpful.
  • Rolland from New Port Richey, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the pr ice of the element plus the cost for the service call.
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people found this instruction helpful.
  • FRANK from CLARENCE CTR, NY
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Was this helpful?
Thank you for voting!
Replace the oven Sensor
3 of 5 people found this instruction helpful.
  • Michael from Exeter, NH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people found this instruction helpful.
  • Georgene from Rock City, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Was this helpful?
Thank you for voting!
the burner element stopped working
2 of 2 people found this instruction helpful.
  • Dominic from Fleetwood, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Unscrewed ceramic stove top , lifted top and exposed element , unscrewed element from top and disconnected wireing (marking wires to assure proper reinstillation .
Took new element and attached to top and returned wires to proper terminals , there was A slight change in wireing but was easy to understand and quick to adjust to new el ement .
Replaced top on stove and rescrewed to secure .
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people found this instruction helpful.
  • francis from mount holley, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Was this helpful?
Thank you for voting!
All Instructions for the 38FK
61 - 75 of 237