38FG Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element burned out, broke circle, heat only half
1 person
found this instruction helpful.
-
Michael from Thornton, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering
... Read more
the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Read less
Was this helpful?
Thank you for voting!
replace element
1 person
found this instruction helpful.
-
alex from huntington, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this helpful?
Thank you for voting!
Oven door was locked, couldn't set oven temps
1 person
found this instruction helpful.
-
William from Nashville, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off)
... Read more
now turned off. That's a lot of things working better for less than $50!
Read less
Was this helpful?
Thank you for voting!
Half of broiler element worked
1 person
found this instruction helpful.
-
Paul from SEATTLE, WA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to
... Read more
new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Read less
Was this helpful?
Thank you for voting!
Oven temperature fluctuates
1 person
found this instruction helpful.
-
Larry from SOLON, IA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this helpful?
Thank you for voting!
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Jennair cooktop with coils lost one of its coil guides.
1 person
found this instruction helpful.
-
Bruce from SOUTHBURY, CT
- Really Easy
- 30 - 60 mins
-
Socket set
We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.
Was this helpful?
Thank you for voting!
F5 fault code kept appearing
1 person
found this instruction helpful.
-
Louis Rodriguez from Granbury, TX
- Very Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed
... Read more
it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Read less
Was this helpful?
Thank you for voting!
Burner plugs were loose
1 of 2 people
found this instruction helpful.
-
James from CONCORD, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
used the supplied parts...very easy. The parts were exact replacements.
Was this helpful?
Thank you for voting!
Oven not heating to desired temp
2 of 5 people
found this instruction helpful.
-
Raymond from Ridgecrest, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab ... Read more le adapter that came with the new sensor was needed in my case.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cab ... Read more le adapter that came with the new sensor was needed in my case.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
1 of 2 people
found this instruction helpful.
-
Ralph from Nicholasville, KY
- Easy
- 30 - 60 mins
-
Screw drivers
Flipped off breaker and removed oven door and pulled built in stove out so the back panel could be removed. Unplugged the sensor then removed the two screws securing the old sensor inside the oven and installed new sensor. Put stove back together and installed back into counter top, re-installed oven door, flipped on the breaker and ove
... Read more
n works like new.
Read less
Was this helpful?
Thank you for voting!
Top oven element works, but bottom element works only intermittently
2 of 5 people
found this instruction helpful.
-
Bruce from Glencoe, MN
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced the long Oven Sensor but have not resolved the root problem. Oven still will not reach required temperature. Bottom element becomes red hot, but turns off and will not start again.
Was this helpful?
Thank you for voting!
burned out stove eye, 6"
1 of 2 people
found this instruction helpful.
-
Robert from Birmingham, AL
- Easy
- 15 - 30 mins
remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan
Was this helpful?
Thank you for voting!
Oven Over Heating
1 of 2 people
found this instruction helpful.
-
Steve from New Albany, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the oven from the wall. Removed back cover and unplugged sensor from the harness. Remove and replace sensor from inside the oven. Reconnect harness and reinstall back cover. Secure oven back into the wall.
Was this helpful?
Thank you for voting!
Just needed new drip pans for burners
1 of 2 people
found this instruction helpful.
-
Ann from Cadiz, KY
- Really Easy
- Less than 15 mins
Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.
Other Parts Used:
Was this helpful?
Thank you for voting!