EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FG Magic Chef Range - Instructions

All Instructions for the 38FG
76 - 90 of 277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not hold temperature, not turn on, and would shut off during use.
1 person found this instruction helpful.
  • John from Arvada, CO
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Phili ps head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Was this helpful?
Thank you for voting!
No problem installing the sensor
1 person found this instruction helpful.
  • tommy from FAYETTEVILLE, NC
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this helpful?
Thank you for voting!
"F3" error message and no oven heat
1 person found this instruction helpful.
  • Pat from PAYSON, AZ
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!
Was this helpful?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
1 person found this instruction helpful.
  • BETH from COUNCE, TN
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Was this helpful?
Thank you for voting!
surface element needed to be replaced along with all the drip Bowls
2 of 4 people found this instruction helpful.
  • Tawnia from SHOW LOW, AZ
  • Really Easy
  • Less than 15 mins
take out the old put in the new
Was this helpful?
Thank you for voting!
ELECTRIC BURNER SUPPORT FELL OFF AND BURNER SOMETIMES WOULD NOT COME ON.
1 person found this instruction helpful.
  • RICHARD from SHOW LOW, AZ
  • Very Easy
  • Less than 15 mins
Stuck the new one into the plugin.
Was this helpful?
Thank you for voting!
2 Service Elements Didn't Work (Didn't heat up)
1 person found this instruction helpful.
  • Roseann from MEADVILLE, PA
  • Very Easy
  • Less than 15 mins
Unplugged old elements and plugged in new ones
Was this helpful?
Thank you for voting!
Couldn't find correct drip bowls that fit.
2 of 4 people found this instruction helpful.
  • Lowell from Hardin, KY
  • Really Easy
  • Less than 15 mins
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Was this helpful?
Thank you for voting!
The old drip bowls were rusting, no chrome left
3 of 7 people found this instruction helpful.
  • kathryn from piqua, OH
  • Really Easy
  • Less than 15 mins
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Was this helpful?
Thank you for voting!
burner would not heat.
1 person found this instruction helpful.
  • Jackie from Hughes Springs, TX
  • Really Easy
  • Less than 15 mins
I unpluged the old burner and pluged the new one in. Repair done in about 2 min,
Was this helpful?
Thank you for voting!
The heating element on the left front burner was out
2 of 4 people found this instruction helpful.
  • Julie from Salt Lake City, UT
  • Really Easy
  • Less than 15 mins
Pulled the old one out and plugged the new one in. It was that simple!
Was this helpful?
Thank you for voting!
oven not heating to set temp. 100 degrees too cold
2 of 4 people found this instruction helpful.
  • Robert from Funston, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this helpful?
Thank you for voting!
Broiler element was only working on one side
1 person found this instruction helpful.
  • Helen from SPRINGFIELD, OH
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.
Was this helpful?
Thank you for voting!
Element in oven would not adjust to the oven temperature.
1 person found this instruction helpful.
  • Dolores from Edmond, OK
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fi sh out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.
Was this helpful?
Thank you for voting!
Burnt out
2 of 4 people found this instruction helpful.
  • David from Elba, AL
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this helpful?
Thank you for voting!
All Instructions for the 38FG
76 - 90 of 277