38FG Magic Chef Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip pans were not original to range, I could not get them clean.
2 of 2 people
found this instruction helpful.
-
Lynn from BRADENTON, FL
- Really Easy
- Less than 15 mins
I reoved old drip pans and installed new ones. Very easy, they look great!
Other Parts Used:
Was this helpful?
Thank you for voting!
Replace the oven Sensor
3 of 5 people
found this instruction helpful.
-
Michael from Exeter, NH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not loo
... Read more
k for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike
Mike
Read less
Was this helpful?
Thank you for voting!
Oven would over heat and produce a F2 error code on the display. It would not turn off or cool down until I switched the circuit breaker off.
2 of 2 people
found this instruction helpful.
-
richard from SAINT MARYS, KS
- Very Easy
- Less than 15 mins
-
Screw drivers
I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.
Was this helpful?
Thank you for voting!
Cooling fan runs fault code displayed
2 of 2 people
found this instruction helpful.
-
FRANK from CLARENCE CTR, NY
- Easy
- 30 - 60 mins
-
Screw drivers
Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it eas
... Read more
ily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done
Read less
Was this helpful?
Thank you for voting!
After cleaning, F1-1 error flashed and neither oven worked
3 of 5 people
found this instruction helpful.
-
Georgene from Rock City, IL
- Easy
- 15 - 30 mins
-
Screw drivers
First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your websit
... Read more
e. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!
Read less
Was this helpful?
Thank you for voting!
The Broiler element split after oven self-cleaning
2 of 2 people
found this instruction helpful.
-
Rolland from New Port Richey, FL
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the pr ... Read more ice of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the pr ... Read more ice of the element plus the cost for the service call.
Read less
Was this helpful?
Thank you for voting!
Maytag range had "F3" code display, oven would not work.
2 of 2 people
found this instruction helpful.
-
phillip from Farmington, NM
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose
... Read more
by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.
Read less
Was this helpful?
Thank you for voting!
No temperature control
2 of 3 people
found this instruction helpful.
-
Max from Houston, TX
- Easy
- 30 - 60 mins
-
Screw drivers
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.
... Read more
Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Read less
Was this helpful?
Thank you for voting!
Frayed and exposed receptical wires in cartridge
2 of 3 people
found this instruction helpful.
-
Richard C from San Jose, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
* Do not lose the supplied CERAMIC electric connecting nuts; they will not fry in the heat.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
* Unplug the heating elements from the old receptacles, and remove any rings; unplug the cartridge by lifting up the back side and pulling gently toward the back of the stovetop.
* Unscrew the cartridge top from the cartridg ... Read more e base (about 12 screws) and the recepticals, and cut the old wire close to the old receptacle.
* If you have a spare magnetic thingy around, use it to hold the screws and not lose them.
* Screw in the new receptacles, route the newer wiring from the receptacles (use as much of the new wire as possible), back toward the wiring block on the cartridge plug.
* Recut the old wiring to accomodate the length of the new wiring, but leave at least 2-3" from the wiring block, if possible. Re-connect them using only the supplied CERAMIC electric nuts.
* The CERAMIC nuts allayed my fears about the effect of heat on a plastic nut; ceramic is designed for high-heat environments.
* Reverse the disassembly steps to reassemble and reinstall the cartridge.
Read less
Was this helpful?
Thank you for voting!
Replaced Broiler Element
2 of 3 people
found this instruction helpful.
-
Phillip from Reston, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this helpful?
Thank you for voting!
Replace clock-adjust knob
2 of 3 people
found this instruction helpful.
-
OSCAR from BRISTOL, CT
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this helpful?
Thank you for voting!
Used part
2 of 3 people
found this instruction helpful.
-
Sabrina from FREMONT, CA
- Very Easy
- Less than 15 mins
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Other Parts Used:
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven Temperature was 50 degrees low
2 of 3 people
found this instruction helpful.
-
Eugene from Clinton, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees
... Read more
low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Read less
Was this helpful?
Thank you for voting!
lamp retainer gasket disintegrated when changed burned out bulb
2 of 3 people
found this instruction helpful.
-
Sandra from Flemington, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this helpful?
Thank you for voting!