EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FG Magic Chef Range - Instructions

All Instructions for the 38FG
46 - 60 of 277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The drip bowls were all caked and corroded.
4 of 5 people found this instruction helpful.
  • Terry from Mountain City, TN
  • Really Easy
  • Less than 15 mins
This wasn't a "repair", but I got an email asking for my story, so here it is. :-)

I followed the owner's manual instructions by pulling out the burner elements, lifting up the old drip bowls, setting in the new ones, replacing the elements.
Was this helpful?
Thank you for voting!
Panel light burnt out after 10 years
4 of 5 people found this instruction helpful.
  • Pamela from La Junta, CO
  • Really Easy
  • Less than 15 mins
I live in a small town in South East Colorado. We have just a Walmart and Sears and a few smaller hardware stores. I checked all of them to try to find this 25 1/2 inch Fluorescent Light Bulb, and nobody carried one. I would have had to drive 70 miles to find one. The Service of Partselect was wonderful and the bulb showed up in just 4 days. I was lost without this light. I have bought a few other items for my older appliances in the past from Partselect. com and was very happy with the service and how easy the web page is to navigate. .
Was this helpful?
Thank you for voting!
Burner no longer worked.
4 of 5 people found this instruction helpful.
  • Marcus from Emmett, KS
  • Easy
  • Less than 15 mins
  • Screw drivers
First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!
Was this helpful?
Thank you for voting!
Old coil broke.
6 of 12 people found this instruction helpful.
  • Paula Collins from Needham, MA
  • Really Easy
  • Less than 15 mins
After I removed the piece of metal separating the two wires, I inserted the unit with no problem.
Was this helpful?
Thank you for voting!
broken terminal
3 of 3 people found this instruction helpful.
  • Gary from Shirley, IN
  • Really Easy
  • Less than 15 mins
Simply removed the old heating element and plug the new element terminals into socket.
Was this helpful?
Thank you for voting!
Oven erratic, not heating correctly, timer beeper sounding
3 of 3 people found this instruction helpful.
  • Dave from SANTA BARBARA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
Was this helpful?
Thank you for voting!
Burned up oven door gasket needed replaced.
7 of 15 people found this instruction helpful.
  • Daniel from Prescott, MI
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt awa y about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this helpful?
Thank you for voting!
Uneven Heating/ High Heat Broiler To No Heat
3 of 3 people found this instruction helpful.
  • Jack from Houston, TX
  • Difficult
  • More than 2 hours
  • Screw drivers
After replacing heating element then selector switch, I came to think the only other thing was the thermostat. It finally worked. . . But not without some tribulations. This note is for a repair involving thermostat for a w130 jenn-air or maytag wall oven, do not follow instructions included with replacement part! It says the br and ba terminals are to be reversed with this replacement part. . . Not so! After re-connecting (as per instructions) nothing worked! If you have this model jennair or maytag, my suggestion is to replace the wires to connections just as they were removed from the old one. I finally did this after much frustration and electrical testing with a multimeter. Hope this note helps someone. Good luck!
Was this helpful?
Thank you for voting!
ovens wouldn't maintain temperature after preheat cycle
3 of 4 people found this instruction helpful.
  • sherri from elk horn, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.p lugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!
Was this helpful?
Thank you for voting!
Burner wouldn't heat (wiring failure)
3 of 4 people found this instruction helpful.
  • Eugene from San Antonio, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench set
1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.
Was this helpful?
Thank you for voting!
i sat a tupperware bowl on a hot burner and it stuck to the burner so i had to replace it
3 of 4 people found this instruction helpful.
  • judy from palatine, IL
  • Really Easy
  • 15 - 30 mins
just plugged it in!
Was this helpful?
Thank you for voting!
piece of cake. The pictures with the grid background on your website gave me ability to verify what I was purchasing.
3 of 4 people found this instruction helpful.
  • George from Irving, TX
  • Really Easy
  • Less than 15 mins
This is the second use of Parts Select. First time was for another obscure part for an old microwave, which also worked out VERY well. Both appliances still in action.
Was this helpful?
Thank you for voting!
Oven would not heat
2 of 2 people found this instruction helpful.
  • francis from mount holley, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
replaced old drip pans
3 of 5 people found this instruction helpful.
  • Frances from Summerfield, FL
  • Really Easy
  • Less than 15 mins
Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!
Was this helpful?
Thank you for voting!
All Instructions for the 38FG
46 - 60 of 277