EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FG Magic Chef Range - Instructions

All Instructions for the 38FG
16 - 30 of 277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven door spring broke and had to be replaced, oven light out and had to be replaced
16 of 19 people found this instruction helpful.
  • Ed from Anderson, IN
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I ha d to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.
Was this helpful?
Thank you for voting!
defective oven sensor
17 of 23 people found this instruction helpful.
  • sean from easthampton, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires to gether and reattached sensor inside oven. A cakewalk.
Was this helpful?
Thank you for voting!
Element burned out
18 of 28 people found this instruction helpful.
  • Anita from Hudson, CO
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unplug Stove removed screws pulled out
element. Lifted off the wires with a pliers they slid
onto the element ends that were pointed up
was very easy.
Was this helpful?
Thank you for voting!
Light Bulb burned out
12 of 12 people found this instruction helpful.
  • Jeffrey from Marietta, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. Th e order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.
Was this helpful?
Thank you for voting!
Code said we needed a sensor
12 of 14 people found this instruction helpful.
  • Janice from Portland, OR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.
Was this helpful?
Thank you for voting!
spring broke on one side of door hinge
14 of 20 people found this instruction helpful.
  • Travis from Lexington, OK
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.
Was this helpful?
Thank you for voting!
oven getting 50 degrees or more, hotter than setting
10 of 10 people found this instruction helpful.
  • Joseph from Wappingers Falls, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.
Was this helpful?
Thank you for voting!
After self cleaning the oven received an error code telling me the sensor was bad.
11 of 13 people found this instruction helpful.
  • Christine from Davie, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working corre ctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )
Was this helpful?
Thank you for voting!
Burner was out but the burner coil worked on onother burner
10 of 10 people found this instruction helpful.
  • Richard from Orange, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Was this helpful?
Thank you for voting!
F1 code and oven wouldn't operate
11 of 15 people found this instruction helpful.
  • Robbie from Hillsboro, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.
Was this helpful?
Thank you for voting!
1998 oven unit flashing F3
10 of 14 people found this instruction helpful.
  • chris from houston, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.
Was this helpful?
Thank you for voting!
Purchased home but stove had no broiler pan.
16 of 33 people found this instruction helpful.
  • Raymond from BLOOMINGTON, MN
  • Very Easy
  • Less than 15 mins
Purchased 2 piece broiler pan from this site
Was this helpful?
Thank you for voting!
burner receptacle burned out
8 of 9 people found this instruction helpful.
  • Michael from N. Haverhill, NH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.
Was this helpful?
Thank you for voting!
Broiler unit would only heat on one side
8 of 9 people found this instruction helpful.
  • Lawrence from Morganton, NC
  • Really Easy
  • 1- 2 hours
  • Screw drivers
Removed the screws that held the element and disconnected it. Placed the new element in the proper place, connected the wiring, and replaced all the screws. The unit worked beautifully, and all is well. My wife is happy.
Was this helpful?
Thank you for voting!
The oven and ranges would not heat up and an F9 error was displaying on the Oven Screen.
7 of 7 people found this instruction helpful.
  • Jared from UNION GROVE, AL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.
Was this helpful?
Thank you for voting!
All Instructions for the 38FG
16 - 30 of 277