EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

38FG Magic Chef Range - Instructions

All Instructions for the 38FG
31 - 45 of 277

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Spring Broke
7 of 9 people found this instruction helpful.
  • Thomas from Van Nuys, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed 7 screws on sides and one on top of stove. Replaced both springs (only one was broken but did both). Took around 15 to 30 minutes from start to finish.Fastest shipping in history during holidays without paying anything extra.
Was this helpful?
Thank you for voting!
my oven would not heat to proper temp
6 of 6 people found this instruction helpful.
  • mark from CHAMBERLAIN, SD
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. T his repair took about 10 mins and the oven works perfectly. Thanks !
Was this helpful?
Thank you for voting!
Stove top wouldn't come on. Oven couldn't go higher than low heat
7 of 9 people found this instruction helpful.
  • Peter from FREDERICK, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answer ed my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland
Was this helpful?
Thank you for voting!
electric coils would not stay flat as drip pans were incorrect fit
6 of 7 people found this instruction helpful.
  • Janet from Philadelphia, PA
  • Really Easy
  • Less than 15 mins
replaced drip pans with correct type
Was this helpful?
Thank you for voting!
no temp control
21 of 53 people found this instruction helpful.
  • Cathreen from Lusby, MD
  • Really Easy
  • Less than 15 mins
  • Screw drivers
very easy
Was this helpful?
Thank you for voting!
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
5 of 5 people found this instruction helpful.
  • Aubrey from EADS, TN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this helpful?
Thank you for voting!
replace light in oven
5 of 5 people found this instruction helpful.
  • william from aiken, SC
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
remove plate, gasket, & light cover then light. .Replace light. Put gasket on plate , insert cover. TAPE PLATE TO COVER ,then screw all in place, remove tape.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people found this instruction helpful.
  • Carl from RIVERSIDE, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
electric burner burned out
6 of 9 people found this instruction helpful.
  • Paul from Foley, AL
  • Really Easy
  • Less than 15 mins
This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartri dge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.
Was this helpful?
Thank you for voting!
Store-bought drip bowls wouldn't fit.
5 of 6 people found this instruction helpful.
  • Sharon from Yacolt, WA
  • Really Easy
  • Less than 15 mins
My elements just plug in so all I had to do was pull them out and replace the drip bowls. They fit perfectly!
Was this helpful?
Thank you for voting!
The heating element socket had crumbled with age.
4 of 4 people found this instruction helpful.
  • Edward from Webster, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.
Was this helpful?
Thank you for voting!
burner fell apart
5 of 7 people found this instruction helpful.
  • Barbara a from Huntington, NY
  • Really Easy
  • Less than 15 mins
Plugged in the new burner, which we received in one day.We were delighted with the quick service
Was this helpful?
Thank you for voting!
Timer know would no longer set the time...
5 of 7 people found this instruction helpful.
  • Rachael from Adams, MA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the swit ch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.
Was this helpful?
Thank you for voting!
Replacement of broil element in wall oven
4 of 4 people found this instruction helpful.
  • David from San Rafael, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw d river is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Was this helpful?
Thank you for voting!
Oven was not correctly heating to set temperature
4 of 5 people found this instruction helpful.
  • Trace from Ofallon, MO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.
Was this helpful?
Thank you for voting!
All Instructions for the 38FG
31 - 45 of 277