3468 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ignitor glows but not hot enough to open the gas valve. It's old.
6 of 6 people
found this instruction helpful.
-
Kenneth from MESQUITE, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My Tappan Tail:
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behi ... Read more nd the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Open the oven and remove the racks, turn on the oven light.
Remove two screws in the back to remove the bottom plate. Mine are about 1 1/4 in. long.
Remove one nut holding the butterfly plate in place. Ignitor will be exposed.
Turn off the oven light and unplug oven. Don't drop the plug behi ... Read more nd the oven, I was ready for that one.
Drop light or flash light will be needed, it's dark in there. And something to sit on, 16" old plastic milk caddy, I just happen to have one.
Remove the two screws holding the ignitor, don't cut the wires just yet. Take note where the wiring runs. Install the new ignitor. My wires went behind the gas piping.
I cut the bottom wire from the old ignitor first, up close to the ceramic. Wire shield can be reused, slide it over the new wire. Cut the old wire, leave a lot. Trim the new wire to desired length and strip the ends of both and use the ceramic cap and connect the wires.
Do the top wire.
Slide the wire shield next to the igniter, adjust the wires so the wire shields won't slide away from ignitor. With the butterfly shield back in place it's time to plug it in and give it a test.
Nice.
Replace the bottom plate of oven, screw holes hard to find. Had to use an awl to find the holes to line up the screws. I also didn't push the front of the plate down into place until I had the screws started. It helped.
You might think this is overkill, but how many of us have ever replaced the ignitor. Not me.
I do a lot of DIY's. I'll rate this as a 1, easy.
What shall I bake first, cornbread of course. I my cast iron skillet.
Read less
Was this helpful?
Thank you for voting!
My range is 13+ yrs old and the knobs and bezels were looking very sad and worn.
6 of 7 people
found this instruction helpful.
-
Susan from Aiken, SC
- Really Easy
- Less than 15 mins
I simply popped off the old ones, cleaned around opening and popped in the new ones.
And what a difference. The old ones were an off white color and I replaced them with white ones. Such an easy way to spruce up the stove!!
And what a difference. The old ones were an off white color and I replaced them with white ones. Such an easy way to spruce up the stove!!
Other Parts Used:
Was this helpful?
Thank you for voting!
black dirty burner grates
14 of 31 people
found this instruction helpful.
-
Carolyn from St. George, UT
- Really Easy
- Less than 15 mins
replaced grates
Was this helpful?
Thank you for voting!
Igniters were flaky on 2 burners and almost dead on 2
7 of 10 people
found this instruction helpful.
-
Matt from Craig, CO
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the uti
... Read more
lity drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Read less
Was this helpful?
Thank you for voting!
Burners would not ignite flame...Had to start with match.
6 of 7 people
found this instruction helpful.
-
Richard from Los Angeles, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Removed the old burners with a Plumbing Pipe Wrench by turning 1/4 turn counter clockwise. Disconnected (2) wires and replaced with new Sealed Burners. The simmer burner wires were slightly diffrent from the original but they do fit by opening the connector with screwdriver and then clamping once wire inserted.
Was this helpful?
Thank you for voting!
Burners would not ignite
6 of 7 people
found this instruction helpful.
-
Charles from Kalamazoo, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed cover from igniter, took off wires, replaced wires on new one, secured in place, put cover back on.
Was this helpful?
Thank you for voting!
spark ignition in stove failed to turn on burnes.
7 of 10 people
found this instruction helpful.
-
David from Upland, CA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical.
... Read more
I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat consistently
6 of 7 people
found this instruction helpful.
-
Leland from Orting, WA
- Easy
- 30 - 60 mins
-
Screw drivers
I needed to remove the rear panel to replace the sensor, but unfortunately, that was not the problem. It could have been; but also, it could have been the electronic control, or the gas control valve. This was the cheapest "trial" fix. I did talk to a "Warranty Repair Man", who said that IF it was the electronic control, because of
... Read more
the age of the oven, (13 years) the part would not be available and would need to be fabricated by the manufacture. Even then the cost would approach the cost of a new oven. So, we abandonded the idea of repairs to this one. I guess 13 years is a bit to much to expect of a machine this day and time. Things are made to use-up and throw away. Such is life ! !
Read less
Was this helpful?
Thank you for voting!
Faulty bulb receptacle
10 of 20 people
found this instruction helpful.
-
Kenneth from Lynchburg, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
Electronic spark ignition would not ignite intermittently.
5 of 5 people
found this instruction helpful.
-
Charles from Old Bridge, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping th
... Read more
e new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
Read less
Was this helpful?
Thank you for voting!
burners corroed by sulphate in the gas
5 of 5 people
found this instruction helpful.
-
Juan Jose from Miami, FL
- Really Easy
- Less than 15 mins
just turn the burners counter clock wise with the help of a jar opener pad. unplug the wire connectors and replace the burners no hassle, no problem. Everything went fine… one thing though, it is not the same color as it was before. I didn’t realize it until opening the box. Previous color was grey. My wife is Ok with it, so I won’t
... Read more
complain, but maybe you should add the color option if there is more than one choice.
Best regards.
Best regards.
Read less
Was this helpful?
Thank you for voting!
the lines were broken
7 of 11 people
found this instruction helpful.
-
RONALD from DELAVAN, WI
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
1) removed 2 lines 2) removed 4 screws 3)pulled out old element4) relaced new part 5)installed screws 6) install lines &tighten
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
both burner heads would not ignite
5 of 6 people
found this instruction helpful.
-
Steven from Warwick, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged the burner heads from the wires, and simply put the wires on the new burner heads and put back onto the stove,. Simple as pie. Very happy that i found parts select online, easy to find the part though your pictures and easy to order.
Loved being able to do this myself without a middle man. Very satisfied!
Loved being able to do this myself without a middle man. Very satisfied!
Was this helpful?
Thank you for voting!
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!