3468 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven won't stay light
10 of 10 people
found this instruction helpful.
-
Shannon from Lake Park, IA
- Easy
- 15 - 30 mins
-
Screw drivers
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.
Was this helpful?
Thank you for voting!
Light Switch Was Broken
12 of 17 people
found this instruction helpful.
-
REY from GAINESVILLE, TX
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
I removed screws that hold cover and put cover aside. I removed the buttons and removed glass cover. I pulled panel out far enough t get tswitch wires and installed switch. Be very careful not to let wires touch metal.
Was this helpful?
Thank you for voting!
Oven Racks needed to be replaced.
11 of 14 people
found this instruction helpful.
-
Peter from Chicago, IL
- Really Easy
- Less than 15 mins
Slide out the old; slide in the new!
Was this helpful?
Thank you for voting!
Oven would not light
9 of 10 people
found this instruction helpful.
-
Matt from Verona, WI
- Easy
- 15 - 30 mins
-
Screw drivers
Make sure you unplug the oven before you begin. I removed the old igniter. The top wire on the igniter goes to the back of the oven and plugs into a flat blade type connector. Instead of using the twist wire nut I used a flat connector because it was easier to put on and is foolproof. Make sure you cut the plastic insulation off the c
... Read more
onnector so it does not melt when the oven is in use. I used a wire nut on the other wire and that was it. Very simple and the oven works great again.
Read less
Was this helpful?
Thank you for voting!
burner didn't self ignite or control flame
9 of 10 people
found this instruction helpful.
-
Geoffrey from Columbus, GA
- Really Easy
- 15 - 30 mins
-
Pliers
The burners turn and lift. I replaced two. One turned very easily, the other was stuck so I used liquid wrench and plumbers pliers. I did get it off. Once off, the old wires slipped right off and onto the new burners. Those twisted on very easily. Good as new easy breezy.
Was this helpful?
Thank you for voting!
Broiler igniter not glowing
11 of 16 people
found this instruction helpful.
-
Steven from Silver Spring, MD
- Easy
- 1- 2 hours
-
Nutdriver
1) Turn off the gas and disconnect the power
2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.
3) Remove the grills.
4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws ... Read more .
5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.
6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.
7) The igniter is now exposed and can be remove by removing the two SD drive screws.
8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.
9)Reverse the above dissembly procedure.
10) Broil the sausages.
2) Remove oven door. There requires that you remove the two square drive (SD) bolts on the inside, partially close the door and lift it off the hinges.
3) Remove the grills.
4) At the back remove the rear shield (aluminum panel held by 2 SD sheet metal screws ... Read more .
5) this exposes the broiler igniter and its two wires. If its been replaced in past, there should be two porcelain screw-on wire connectors. Undo the connectors by turning them counter-clockwise. With a volt-ohmmeter, measure the resistance across the igniter. If its open circuited, its broken. If not, then its in the circuit board, and this help stop here. If this is the original igniter, it ends in a plastic connector. Disconnect by pulling it apart from its mating plug and again, check the continuity of the igniter. If its defective, reconnect the connector and cut each wire on the igniter side. Strip back about 1/2 inch of insulation on each lead.
6) inside the oven, using the SD driver, remove the 4 screw securing the broiler burner from the roof of the oven. The burner can now be removed, pulling the burner away from the gas jet on the right.
7) The igniter is now exposed and can be remove by removing the two SD drive screws.
8) Replace with the new igniter, being careful not to touch the black element, and feeding the wires though the rear oven wall.
9)Reverse the above dissembly procedure.
10) Broil the sausages.
Read less
Was this helpful?
Thank you for voting!
The oven would not fire up.
12 of 19 people
found this instruction helpful.
-
edward from smithtown, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I searched the item I needed and followed a link to PartSelect.com. I paid a little extra for shipping and literally recieved the part in two days. The part was an absolute perfect fit and my wife and myself have never been happier. Home cooked meals again thanks to the folks at PartSelect.com. It couldn't have been an easier.
Was this helpful?
Thank you for voting!
Oven would not preheat and gave 'F1' error
9 of 11 people
found this instruction helpful.
-
Joshua from Reno, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
Was this helpful?
Thank you for voting!
inner glass busted
9 of 11 people
found this instruction helpful.
-
robert from orange, CA
- Easy
- 15 - 30 mins
-
Screw drivers
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.
Replaced screws and handle,pulled hinge's out to first stop and sli ... Read more d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great.
Thanks Bob G.
Replaced screws and handle,pulled hinge's out to first stop and sli ... Read more d door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great.
Thanks Bob G.
Read less
Was this helpful?
Thank you for voting!
Cracked gas feed tubes
9 of 11 people
found this instruction helpful.
-
Jeff from Union City, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
CAUTION: DO NOT LIFT RANGE TOP AS IT WILL CRIMP YOUR GAS FEED TUBES!!!
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Remove grates and drip covers. Twist each burner counter clockwise and lift off. Remove ground wire and ignitor wire from each burner. Remove screws that holds the Orifice/Tube assy to the range top (one where each burner was) You might have to remove the or ... Read more ange rubber flanges if they didn't stay on the burners to see the screws.
Now lift (or remove) your range top to get access to the tube assy. Take a wrench and remove each gas tube nut (2 for each assy) and remove the old assy.
Drop each new Tube assy in and reverse the procedure.
Read less
Was this helpful?
Thank you for voting!
F-3 error code
8 of 8 people
found this instruction helpful.
-
Mark from Lake Orion, MI
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Was this helpful?
Thank you for voting!
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
9 of 11 people
found this instruction helpful.
-
Crystal from Scott City, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now ju
... Read more
st like a new oven.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 8 people
found this instruction helpful.
-
Treasure from High Point, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I tur ... Read more ned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !
Read less
Was this helpful?
Thank you for voting!
Original oven light lens had cracked and broken in two.
17 of 36 people
found this instruction helpful.
-
Pat from Bucklin, KS
- Really Easy
- Less than 15 mins
I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).
Was this helpful?
Thank you for voting!
oven would not light -igniter was on
9 of 12 people
found this instruction helpful.
-
Tom from South Amboy, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
removed shelves and base, removed 2 screws that held igniter on, disconnected wires from gas valve removed protective cover in corner {1 screw}
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
disconnected plug, removed igniter. This igniter was easier to remove from front of stove on this model
Was this helpful?
Thank you for voting!