EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3468 - Instructions

All Instructions for the 3468
46 - 60 of 787

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven stopped while the wife was cooking.
15 of 18 people found this instruction helpful.
  • Marsha from Concord, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws hol ding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!
Was this helpful?
Thank you for voting!
Sealed burner caps were rusted within and gas leak through the bottom of the caps
13 of 13 people found this instruction helpful.
  • j from bridgewater, NJ
  • Easy
  • 15 - 30 mins
Just used a car oil filter band type wrench and rotated the sealed burner cap a 1/4 turn. cleaned up the rust and dirty. Replaced it with the new cap and tightened it with a 1/4 turn by hand. Instruction can be found on Maytag gas installation manual. The burners are working well and just like a new range.
Was this helpful?
Thank you for voting!
My wife destroyed the oven door seal with oven cleaner...
14 of 16 people found this instruction helpful.
  • David from Bexley, OH
  • Really Easy
  • Less than 15 mins
I ordered the part one afternoon. It arrived before noon the next day. Then I simply removed the old seal (with about 2 dozen spring clips). Inserted the new part by carefully inserting the new seal into its corresponding hole at each end and then worked my way around the seal while inserting each attached spring clip into its correspon ding hole.
Was this helpful?
Thank you for voting!
Oven would not heat up
13 of 14 people found this instruction helpful.
  • Micah from Hallettsville, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Checked internet for possible reasons why oven would not heat.

Found Partselect.com website. Searched and found that ignitor was probably the problem.

Put in my oven model number and found ignitor. Ordered ignitor.

When new ignitor came in I simply removed two screws that held old ignitor and disconnect ed two wire.
Put new ignitor on, replaced screws and wires.

Repair done and oven works great.
Was this helpful?
Thank you for voting!
Gas Oven did not come on. Broiler worked.
13 of 14 people found this instruction helpful.
  • Charles from STAR, ID
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.
Was this helpful?
Thank you for voting!
Broken drawer glide
13 of 15 people found this instruction helpful.
  • Peter J from Valparaiso, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
As I pulled the drawer looking for a pan stored in bottom drawer the drawer glide broke. The pictures of the parts were fantastic. Not being sure of which of two parts from the photos, I ordered two parts knowing that hopefully one would be the correct one and the other would not be the part I needed. Parts arrived and it was clear whic h of the two parts would fit perfectly.

I screwed in the part, and that was it , and I was relieved that the problem was solved! I kind of feel lucky that your company is in business! The other part is fully accepted and plan to send it back in for a refund. And oh yes, I solved my appliance problem under $20.00 - unbelieveable these days!

Thank you again for beng there!
Was this helpful?
Thank you for voting!
Ignitor burnt out
14 of 18 people found this instruction helpful.
  • Gregg from Naukati, AK
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I removed the broiler burner assembly held in by 5 screws across the inside top of the oven, as I removed the assembly the igniter slid out from the back of the oven and was attached to the assembly with a cannon plug, I disconnected the cannon plug and removed the whole assembly out of the oven and replaced the igniter which was attached by two screws and reassembled in the oven. Where I live in remote Alaska calling a repair technician is not an option, either figure it out or have a new appliance barged in.
Was this helpful?
Thank you for voting!
Burners would not light and the flame would come out from the bottom of the burner.
13 of 15 people found this instruction helpful.
  • juan from aurora, IL
  • Easy
  • 15 - 30 mins
A quarter turn counter-clockewise and the burner came out. Disconnect the old wires and connect the new wires. Place the burner in its place and a quarter turn clockwise and it was set.
Was this helpful?
Thank you for voting!
Two top burners would not light, defective switch
12 of 14 people found this instruction helpful.
  • Donald from Middle Village, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a m inute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.
Was this helpful?
Thank you for voting!
oven would't go on
12 of 14 people found this instruction helpful.
  • James from Fords, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!
Was this helpful?
Thank you for voting!
burner head was rusted out. ordered 1 to see if part was correct. ordered 4 more to finish job.
13 of 17 people found this instruction helpful.
  • Robert from Somerville, TN
  • Really Easy
  • Less than 15 mins
unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.
Was this helpful?
Thank you for voting!
oven would not maintain temp
12 of 14 people found this instruction helpful.
  • doyle from demorest, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor
Was this helpful?
Thank you for voting!
Oven door wouldn't close or open all the way
14 of 20 people found this instruction helpful.
  • Michael from St. Cloud, MN
  • Easy
  • 30 - 60 mins
  • Screw drivers
1st removed the sealed burners
2nd removed stove top
3rd removed oven door
4th removed left and right side pannels to access door hinges
5th removed left and right hinges
6th installed new left and right hinges
then re-installed other components in reverse order.
The oven door now opens and closes proper ly, the heat stays in the oven!!
Was this helpful?
Thank you for voting!
Oven wouldn't heat up / ignitor was bad
11 of 12 people found this instruction helpful.
  • Timothy from Sandusky, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver
Our original oven ignitor went bad. The gas supply won't even open, unless the oven senses the proper voltage / resistance across the ignitor, so that gas won't be flowing without ignition.

PartSelect was very good about providing me with the proper part, after I got the part number from their schematics and wiring diagrams, on the website. The first replacement part actually arrived, broken, from shipping, but when I called them, they immediately reprocessed the order, and sent me a new ignitor, to arrive the following day. I was very satisfied with their professionalism, as I've been in the past with them, as well.

On to the actual repair:

I removed the broiler drawer from the drawer slides, reached under the main oven chamber, unscrewed the two screws holding the ignitor in place, and cut / disconnected the two wires supplying the power to it.

I then put the new ignitor in place and screwed it back to the mount, used the wire nuts that came with the new ignitor to reconnect / splice the wires, and put the broiler drawer back in place.

Oven fired right up!

Entire process took less than 35 minutes. (Likely would've taken a bit longer, but this is the second replacement for the ignitor, since we've owned this oven, so I already had a good idea how to do it. (The first replacement for this particular part was NOT from PartSelect, so we're hopeful this one lasts a while longer than the previous one.)

Thanks, PartSelect!
Was this helpful?
Thank you for voting!
Spring on hinge broke. Door wont close totally
12 of 15 people found this instruction helpful.
  • Thomas from Baton Rouge, LA
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set
Using the description on the first DIY, I did as told. All went well until the part about removing the panel to access the hinge. There isn't a "panel" on the side of this particular model of Magic Chef stove. You have to remove the entire side of the stove, and then, there's another panel inside of this one. That too has to come off. On ce off, you're into the insulation surrounding the oven. Ain't pretty, I'll assure you. Then, the replacement hinge has holes in it for the mounting screws. The holes aren't threaded, and you have to replace the screws that come with the hinge with self-tapping screws. Either that, or thread the holes with a tap. Thank goodness my wife loves the stove, or it may have just gone out the door. This is not one of Magic Chefs better ideas. Either that, or they didn't plan on having to replace the hinge before the stove wore out.
Was this helpful?
Thank you for voting!
All Instructions for the 3468
46 - 60 of 787