EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3468 - Instructions

All Instructions for the 3468
16 - 30 of 787

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter glows but oven will not light
52 of 60 people found this instruction helpful.
  • James from Virginia, IL
  • Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
The igniter has to be drawing atleast 3 amps for the gas valve to open. If it only draws 2.6 amps like the one i replaced it, the oven won't light.
Was this helpful?
Thank you for voting!
Oven light receptacle broken - bulb base broke off
69 of 118 people found this instruction helpful.
  • Paul from Spokane Valley, WA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
Was this helpful?
Thank you for voting!
drawer glide on bottom stove drawer broke
69 of 131 people found this instruction helpful.
  • Homer from Thomaston, GA
  • Really Easy
  • Less than 15 mins
Snapped the new part into the slot the old one had been in.The repair including opening and closing the drawer took less than a minute.
Was this helpful?
Thank you for voting!
Oven took too long to light, then it didn't light at all
43 of 54 people found this instruction helpful.
  • JULIE from CLOVIS, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
1: Remove oven door.
2: Remove bottom shield, slide in.
3: Remove flame deflector four (4) screws, nut driver.
4: Remove igniter, two (2) screws, nut driver.
5: Remove lower drawer, slide in.
6: Remove wire shield, two (2) screws, nut driver.
7: Disconnect two (2) wire nuts, hands
8: Remove old igniter, hands
9: Install new part in reverse order...

I should have ordered it earlier. It was so easy to install. At first, the oven took 1 minute to light, then, a bit longer, finally around 20 minutes, I told my husband that he needs to get it fixed. So, finally when it wouldn't light at all... I ordered the part and had him install it. It took less than 15 minutes, listening to him the whole time. Now it's wonderful, like a new oven again. Lights up like it should.

Great part selection. Fast service. Thank you
Was this helpful?
Thank you for voting!
glow bar would light but oven would not light
39 of 42 people found this instruction helpful.
  • David from Van Nuys, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
I removed the rear access panel on the oven in order to get to the igniter wires. While testing the output voltage of the old igniter when on, I found that it was producing less than 3 volts ac. This was my clue that although the igniter glowed, it was going bad and needed to be replaced. I unpluged the oven, shut off the gas feed to the oven then removed the oven bottom pan (pull two push pins back, lift up and out) and removed the burner baffle wing nut with baffle. This gave easy access to the igniter and it's two mounting screws which i removed using a phillips screw driver. I unpluged the old igniter from the connector, pluged in the new one after routing it through the access hole from inside the oven to the back of the oven where the connector is located.
Mounted the new igniter, replaced the burner baffle, baffle nut, oven bottom, rear access panel cover, checked and turned on the gas, plugged the oven back in and sure enough it fired up right away. if you check the system of how your oven works and find the problem, it's easy to fix it yourself and save serious money...and look like a hero to the rest of the family.
Was this helpful?
Thank you for voting!
Oven would not heat but broiler would.
37 of 43 people found this instruction helpful.
  • Edward from Sewickley, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
By undoing the bottom of the stoves back panel, you are able to remove the two knock outs and ben the panel up for complete access. Remove gas line and electrical connection (with stove unplugged and main gas valve turned off). Undo the mounting screws and replace unit following steps in revcerse.
Was this helpful?
Thank you for voting!
The oven took too long to ignite (3-5 minutes), or didn't ignite at all. Same description as others on this site.
33 of 35 people found this instruction helpful.
  • Glenn from Jenison, MI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Turned off the breaker to the oven. Took out the racks and oven floor. Took out the steel deflector that sits on top of the oven burner itself (one bolt/washer). Removed the two bolts holding the igniter. Pulled the old igniter around the other side of the burner to be able to better access the wires. There was a woven sleeve around the e nds of the wires, pulled those down the wire to expose the connection. There was an inline connector about 2-3 inches from the igniter, and normal wire after that. I cut the wires where that connection was made and stripped 3/8 inch off the cut wires. Then I cut the wires of the new igniter to the same length as what remained on the old igniter, stripped 3/8 inch off of those, paired them up and used the ceramic wire nuts that came with the new part to make the new connections. Put it all back together, and fired it up. It works wonderfully!
Was this helpful?
Thank you for voting!
No spark at top burners, first one then eventually all 4.
35 of 41 people found this instruction helpful.
  • jonathan from Bryson City, NC
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, locate d inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks!
Was this helpful?
Thank you for voting!
Burner Was Worn Out
31 of 32 people found this instruction helpful.
  • arnold from la punte, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Burner head arrived when I got home from work. Just timely to cook for dinner that monday night, got the 4 burners disconnect the element from the old burner, then connect element to the new bunners, in less than 10 mins, and I had save estimate $600 buying a brand new stove or gas range, this will last me another5 to 10 years. Espec ially this time of recession
Was this helpful?
Thank you for voting!
Burner wouldn't start
35 of 48 people found this instruction helpful.
  • Yury from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
Make a quarter turn counterclockwise, disengage a burner head, disconnect 2 wires, connect to a new head, install turn clockwise.

That's it!
Was this helpful?
Thank you for voting!
Oven would not light
29 of 30 people found this instruction helpful.
  • Richard from Austin, TX
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
This oven was located in a rental house I own.

I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.

Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.

I nex t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.

With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.

The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.

I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.

I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.

I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
Was this helpful?
Thank you for voting!
Oven would not heat- Beeped nonstop and flashed F3
29 of 33 people found this instruction helpful.
  • Erin from Greenwich, CT
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voi la!! The oven turned on and now it works like new!!!
Was this helpful?
Thank you for voting!
Oven wouldn't heat up : (
28 of 32 people found this instruction helpful.
  • Janet from Hampton, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
It was amazingly easy! I am a woman who was a little afraid to deal with wires. But it was just so super easy! And, I saved a bundle by doing it myself! Here's how I did it:
(1) UNPLUGGED OVEN FROM WALL!!!
(2) Remove floor of oven (1 screw)
(3) Remove large metal strip underneath oven floor (2 screws)
(4) R emoved oven igniter (2 screws)
(5) Marked top wire of old igniter before cutting
(6) Cut both wires close to old igniter
(7) Removed a little of the covering of the old wires to expose bare wire
(8) Matched up old top wire with new top wire & twisted both old wires to the new wires
(9) Replaced all screws and oven parts
Was this helpful?
Thank you for voting!
oven takes a long time to reach temp set point
23 of 25 people found this instruction helpful.
  • Scott from Brooklyn Park, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
Was this helpful?
Thank you for voting!
Oven would not ignite
24 of 31 people found this instruction helpful.
  • Bob from Crystal Lake, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Step one - Diagnose. Used a clamp-on ammeter around the igniter lead to check if 3.6 amps or greater were present during ignition. Only about 2.5 amps were measured, indicating that the igniter was bad.

Step two - Ordered the part.

Installation - Removed the racks and bottom oven compartment cover plates, exposing the igniter/burner assembly. Removed the bottom drawer, cut the wires of the existing igniter (leaving plenty of wire left for the new one). Removed the igniter/burner assembly through the oven compartment. Removed the old igniter from the burner, installed the new one. Re-seated the igniter/burner assembly, routing the wires appropriately. Stripped the existing leads (cut in previous step), spliced the new leads in, soldered the connection (soldering is optional). Taped up the splices with electrician's tape. Turned on the oven to verify that the new igniter glowed and the burner lit. Turned off the oven and waited for the burner to cool. Replaced the bottom cover plates and rack.

Final step - Baked some bread.
Was this helpful?
Thank you for voting!
All Instructions for the 3468
16 - 30 of 787