EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3468 - Instructions

All Instructions for the 3468
31 - 45 of 787

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven burner would not come on.
20 of 20 people found this instruction helpful.
  • Theodore C. from Winsted, CT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
Was this helpful?
Thank you for voting!
Kept getting F3 errors
21 of 23 people found this instruction helpful.
  • Daniel from Long Beach, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
My oven stopped working and the display read F3 error. I looked up the code and found that it was probably the thermostat sensor. I ordered the part from partselect.com and when it arrived I went to install it but I ran into a somewhat scary issue. I found that I had to pull my oven out of the wall in order to replace the sensor.

After a minor nervous breakdown, I decided to go for it and found that it was much easier than I had imagined. Changing the sensor involves taking out the two screws that hold the sensor in place (inside of the oven), pulling it out to the point you can reach the connector, plugging in the new sensor and screwing it back in place. However, if you have an oven like my model, you have to pull out the whole oven from the wall in order to reach the plug on the sensor. This sounds like a lot of trouble but for me it was very easy. The oven is held in place with screws around the front side. Most are easily accessed and you don't have to take out any critical/complicated pieces of the oven. My screw gun made short issue of the problem and I found that the oven was out of the wall within minutes. I could then easily unscrew a small back cover, change the sensor and then screw the oven back into the wall. Being very careful, the whole operation took about 20 minutes. I recommend that you get help from a friend just because the oven is bulky. It is not heavy, an average sized male can handle the weight but it’s easier with a friend. Also, be careful that the gas hose which feeds the oven is long enough (and not tangled) for you to move the oven out of its space. Obviously, be careful about gas leaks.
Was this helpful?
Thank you for voting!
Oven would not light -- gas smell
22 of 27 people found this instruction helpful.
  • Mark from Rockwall, TX
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set, Wrench (Adjustable)
Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also instal led ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.
Was this helpful?
Thank you for voting!
Long time to light, strong gas smell
18 of 18 people found this instruction helpful.
  • Kevin from DeRuyter, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver
Unplug power, remove draw, marked and cut wires, unscrewed and removed old igniter, replaced and screwed new igniter into position, reconnected wires with supplied porcelin wire nuts, replace draw, plug in and tried...working great.
Was this helpful?
Thank you for voting!
igniter would light----gas valve would NOT open
21 of 28 people found this instruction helpful.
  • Robert from SALEM, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas ... Read more />CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER
Was this helpful?
Thank you for voting!
missing oven racks
20 of 25 people found this instruction helpful.
  • ALLAN from APACHE JUNCTION, AZ
  • Really Easy
  • Less than 15 mins
order pcs fit perfect.
Was this helpful?
Thank you for voting!
Burners would not ignite
19 of 23 people found this instruction helpful.
  • Craig from Sequim, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.
Was this helpful?
Thank you for voting!
Oven wouldn't lite
20 of 27 people found this instruction helpful.
  • E Blake from Dauphin Island, AL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.
Was this helpful?
Thank you for voting!
oven comes on to temp but will not reheat to a new temp third time trouble with same range
17 of 18 people found this instruction helpful.
  • william from newport, VT
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you
Was this helpful?
Thank you for voting!
oven temperature not correct
16 of 16 people found this instruction helpful.
  • Wayne from Hopedale, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven . Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.
Was this helpful?
Thank you for voting!
Push Pad That Controls The Oven,Temp, Clock Timer Blew Out.
19 of 26 people found this instruction helpful.
  • Joanne from Bridgeport, CT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I did the repair exactly as you described. Transferred each wire over individually to new panel. Now it works like new. My 86 year old mom is so happy she can still bake her christmas cookies. Thank you so very much for your help. I can't believe I did it!!!!!! And saved time and money. Joanne in bridgeport, ct.
Was this helpful?
Thank you for voting!
cracked gas tubes
17 of 21 people found this instruction helpful.
  • Lance from Overland Park, KS
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
My front burners were inoperative because the metal gas lines under the cooktop were cracked. This happened because I tried to remove the cooktop without properly removing the screws holding the assembly to the cooktop. Doh!

Anyway, this is an easy fix. First, remove the 4 burner tops by rotating them counterclockwise and li fting them out of the cooktop. Then, remove the two ignitor wires from each burner, and set the burners aside.

Next, remove the four small screws that hold the burner tube assemblies to the underside of the cooktop. There is one screw near each burner hole in the cooktop (the screws are covered when the burner tops are installed). You must remove all four screws even if you are only installing one replacement orifice and tube kit!

Now you can tilt the cooktop up and remove it from the stove, exposing the orifice and tube assemblies. Use an adjustable wrench to loosen the brass nuts connecting the gas tubes to the valves, and remove the assembly.

Reassemble in reverse order.

If you have "high speed" burners, remove the orifice that comes on the unit and replace it with the loose orifice that is in the packaging.
Was this helpful?
Thank you for voting!
Gas oven took longer and longer to light off even though glow igniter was glowing. When the time grew to 10 minutes and more I knew a repair was needed.
15 of 16 people found this instruction helpful.
  • Joseph from West Hartford, CT
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to g et behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.
Was this helpful?
Thank you for voting!
Oven progessively taking longer and longer to preheat
15 of 16 people found this instruction helpful.
  • Diane from Westmont, NJ
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Disconnect appliance from electricity source! Removed oven grates and the solid oven floor by removing the two screws and lifting up. Removed the piece of metal covering the oven igniter. Unscrewed oven igniter, snipped the wires close to the old igniter (read some of the better descriptions on how to do this). Reconnected new wires to the existing ones and used the ceramic wire covers that came with the new igniter and pushed the wires back through the opening in the rear of the oven. Screwed the new igniter in place. We actually had to unscrew the little metal box on the back of the oven to get to the wires which was easier to work there with connecting the wires. It was a little difficult reaching into the stove since we didn't remove the oven door.
Was this helpful?
Thank you for voting!
Overshooting temperatures upon changing settings
15 of 17 people found this instruction helpful.
  • James from Palmdale, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.
Was this helpful?
Thank you for voting!
All Instructions for the 3468
31 - 45 of 787