3468 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not heat but Broiler would
8 of 9 people
found this instruction helpful.
-
Robert from Hudson, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wr
... Read more
ench. Lift the valve out. Reverse the steps to install the new valve.
Read less
Was this helpful?
Thank you for voting!
Oven would not light
8 of 9 people
found this instruction helpful.
-
Ronald from LONG BRANCH, NJ
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Working on an old oven is difficult. Please expect the unexpected. The years of heating and cooling play havoc with oven parts. The screws holding the Flat Style Oven Ignitor become stripped. It took extra time to remove them. I had to go to the hardware store to buy replacement screws. Once I removed the old parts and had replacement
... Read more
screws the job was very easy.
Read less
Was this helpful?
Thank you for voting!
The oven would take forever to heat up, and sometimes not at all. Othertimes it would heat up, but not stay hot for the entire baking time.
7 of 7 people
found this instruction helpful.
-
Jason from Los Angeles, CA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of t
... Read more
he oven and it popped right out.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
Read less
Was this helpful?
Thank you for voting!
burners rusted out on one side since the stove is 19 years old
8 of 10 people
found this instruction helpful.
-
Elizabeth from Johnstown, PA
- Really Easy
- Less than 15 mins
Bought two to try out to see if they fit and worked-popped out the old ones and the new ones fit and worked like a new stove. Came back to this web site and bought the other two so all burners are now brand new without having to replace the stove.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Oven light bulb went dark; it needed replacing
10 of 17 people
found this instruction helpful.
-
Lise from CEDAR GROVE, NJ
- Very Easy
- Less than 15 mins
Twisted replacement bulb into place easily. Let there be light!
Was this helpful?
Thank you for voting!
Inner Galls on door was craked
8 of 11 people
found this instruction helpful.
-
Randall from Katy, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
Other Parts Used:
Was this helpful?
Thank you for voting!
oven temperature not reaching setting/temp. up and down
7 of 8 people
found this instruction helpful.
-
Ellen from Schenectady, NY
- Easy
- 15 - 30 mins
-
Screw drivers
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
Was this helpful?
Thank you for voting!
Oven temperature lower then setpoint.
7 of 8 people
found this instruction helpful.
-
Robert from Massapequa, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove
... Read more
and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Oven would stop heating after a few minutes of operation
6 of 6 people
found this instruction helpful.
-
John from Ashland, OR
- Easy
- Less than 15 mins
-
Pliers
Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull
... Read more
the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.
Read less
Was this helpful?
Thank you for voting!
Oven racks rusted
11 of 21 people
found this instruction helpful.
-
Wendell from Ocala, FL
- Really Easy
- Less than 15 mins
Ordered new racks and replaced them.
Was this helpful?
Thank you for voting!
F3 code, oven wouldn't heat.
8 of 12 people
found this instruction helpful.
-
Shaun from Kimball, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
First pulled the oven out and noticed how dirty the floor was underneath. Bachelors are BAD housekeepers. Next I removed the oven door (just slides off the hinges) to make it easier to reach in and unscrew the two screws holding the sensor in place in the upper left back of oven. Screws came out easily. Then I removed the back panel by re
... Read more
moving the six screws holding it in place. I unsnapped the temp sensor wiring connection, then pulled the probe out from the front (inside the oven). Installed the new probe by feeding the wires and connector through from the front (inside the oven) and attached it with the two screws. Then went to the back again, snapped the wiring connectors together, and replaced the back panel. Then I scrubbed the floor, pushed the range back in place, reinstalled the door, and gave it a test run. PERFECTION! Heated to within five degrees of setting. EASIEST REPAIR JOB I'VE EVER DONE!
Read less
Was this helpful?
Thank you for voting!
drip pans were scratched
7 of 9 people
found this instruction helpful.
-
rhonda from harpswell, ME
- Really Easy
- Less than 15 mins
We easily inserted the double drip pans under the gas trivets - looks great and we're very satisfied with the product.
Was this helpful?
Thank you for voting!
The F3 error code displayed and beeped during use of the oven and oven shut down.
7 of 9 people
found this instruction helpful.
-
Debra from Colts Neck, NJ
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who
... Read more
added their comments! They gave us courage to give it a try.
Read less
Was this helpful?
Thank you for voting!