3468 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Light bulb went out
7 of 12 people
found this instruction helpful.
-
ANGELA from MEBANE, NC
- Very Easy
- Less than 15 mins
I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.
Was this helpful?
Thank you for voting!
gas oven won't light
5 of 7 people
found this instruction helpful.
-
James from GRASS VALLEY, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
get liquid wrench, remove oven door(2 screws) remove oven bottom(2 screws) follow directions included with part. unplug or shut off electricity at breaker panel, Have a good light source.
Was this helpful?
Thank you for voting!
Oven Igniter stopped working
5 of 7 people
found this instruction helpful.
-
Brian from San Francisco, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
First I turned off the circuit breaker to the oven. Then, I removed the base of the oven (the oven floor) by easily removing two screws. I also removed the flame guard by removing a screw. That easily exposed the old oven igniter. I removed the two small screws that held that in place. The igniter is connected by two wires, which you
... Read more
'll have to snip. Snip those very close to the igniter (leave about an inch of wire on the igniter). Using a wire stripper, remove about 1/2 inch of the outer sheath of the existing wires. On the new igniter, snip the wires leaving about 2 inches still connected to the igniter. Using the wire stippers, remove about 1/2 inch of the outer sheath. Using the plastic wire caps that came with the new igniter, connect the wires from the oven to the corresponding wire on the new igniter. Screw the new igniter back in place. Replace the flame guard and oven floor. Turn on the circuit breaker and start cooking again!
Read less
Was this helpful?
Thank you for voting!
Oven would not maintain temperature
5 of 7 people
found this instruction helpful.
-
KATHY from PLEASANT GAP, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is l
... Read more
ike new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.
Read less
Was this helpful?
Thank you for voting!
Oven wasn't staying on and or re-lighting, recycling to maintain the set Temp.
4 of 4 people
found this instruction helpful.
-
michael from MILFORD, CT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire
... Read more
nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.
Read less
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people
found this instruction helpful.
-
John from Wisconsin Rapids, WI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi
... Read more
th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Read less
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people
found this instruction helpful.
-
Michael from Secaucus, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment.
... Read more
Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Needed to replace the oven door gasket/seal
4 of 5 people
found this instruction helpful.
-
Daniel from Katy, TX
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old
... Read more
gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.
Read less
Was this helpful?
Thank you for voting!
Door hinges broke and stuck/broken light bulb
9 of 20 people
found this instruction helpful.
-
Kenneth from Zachary, LA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I killed power
Pulled the back panel
Pulled the door off
pulled light socket wires
reached in and bent in light socket tabs
knocked out light socket
slide in new socket
lifted top of stove (glass)
disconnected glass top wiring
pulled off glass top
pulled both side panels
removed both ... Read more hinges,
installed new hinges
reinstalled side panels
reinstalled glass top,
reinstalled light socket wiring
installed back panel
installed door
restored power
Pulled the back panel
Pulled the door off
pulled light socket wires
reached in and bent in light socket tabs
knocked out light socket
slide in new socket
lifted top of stove (glass)
disconnected glass top wiring
pulled off glass top
pulled both side panels
removed both ... Read more hinges,
installed new hinges
reinstalled side panels
reinstalled glass top,
reinstalled light socket wiring
installed back panel
installed door
restored power
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broken door hinge
7 of 14 people
found this instruction helpful.
-
James from Elmont, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
unplug unit remove rear panel screws lift up stove top remove top two screws remove panel remove two hinge screws remove replace hinge and follow in reverse order
Was this helpful?
Thank you for voting!
Hammered Orifice tubes
4 of 5 people
found this instruction helpful.
-
Devin from Santaquin, UT
- Easy
- 15 - 30 mins
-
Wrench set
1. Screw the burners counterclockwise 45 degrees to remove each burner. Some gave easily while others were baked on.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. atta ... Read more ch the new assembly and follow steps 1-4 in reverse order.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. atta ... Read more ch the new assembly and follow steps 1-4 in reverse order.
Read less
Was this helpful?
Thank you for voting!
the burner cap on my maytag gas range was rusty on the inside and didn't allow the cap to sit flush-causing gas and flames to leak from under the cap
4 of 5 people
found this instruction helpful.
-
julie from harrodsburg, KY
- Really Easy
- Less than 15 mins
installation was very simple and took less than 5 minutes. first unscrew the burner cap and then remove the 2 wires. to replace reconnect the 2 wires to the new cap and twist cap into place-simple.
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people
found this instruction helpful.
-
peter from marine city, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f
... Read more
ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Read less
Was this helpful?
Thank you for voting!
oven would not come to set heat
4 of 5 people
found this instruction helpful.
-
Ralph from Portsmouth, NH
- Really Easy
- Less than 15 mins
-
Screw drivers
slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people
found this instruction helpful.
-
Linda from Oneida, NY
- Really Easy
- Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!