EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3468 - Instructions

All Instructions for the 3468
121 - 135 of 787

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The neon tube over the stove top went out
8 of 17 people found this instruction helpful.
  • Gunther from Columbia, SC
  • Really Easy
  • Less than 15 mins
Put a new one in.
Was this helpful?
Thank you for voting!
One of four burners did not start (no sparks)
5 of 8 people found this instruction helpful.
  • Nataly from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
Turned burner about a quarter of a turn, lifted, disconnected wires, connected them to a new burner and replaced it.
Was this helpful?
Thank you for voting!
Just unscred the 2 screw on the Thermometer
4 of 5 people found this instruction helpful.
  • WILLIAM J from JERSEY CITY, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.
Was this helpful?
Thank you for voting!
Door gasket was hard and brittle from baked-on grease - heat leaking around door
4 of 5 people found this instruction helpful.
  • Harlen from Spring Creek, NV
  • Really Easy
  • Less than 15 mins
Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.
Was this helpful?
Thank you for voting!
replacing oven racks
4 of 5 people found this instruction helpful.
  • Lawrence from Elmira, NY
  • Really Easy
  • Less than 15 mins
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)
Was this helpful?
Thank you for voting!
Old racks had melted plastic on them.
4 of 5 people found this instruction helpful.
  • James from PAINESVILLE, OH
  • Very Easy
  • Less than 15 mins
It was a replace racks not repair. No problem
Was this helpful?
Thank you for voting!
oven very slow on heating up up to five minutes to ignite.
4 of 6 people found this instruction helpful.
  • manny from oakland, NJ
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
First removed oven racks then two screws to remove oven door, removed two screw of oven fan cover, ( need to remove fan cover to have clearance to removed bottom cover of oven) removed bottom cover of oven, then removed two screws holding oven igniter and cut wires of old igniter then spliced wire of new igniter to existing wire and reassemble in reverse order.
Was this helpful?
Thank you for voting!
Gas was escaping from underneath the burner head
3 of 3 people found this instruction helpful.
  • Edward from ALEXANDRIA, VA
  • Easy
  • 30 - 60 mins
  • Pliers
The old burner head had corroded allowing gas to come out at the bottom. The actual replacement is just turning the head, lifting it out, transferring two wires with slip-on connectors from the old burner to the new one, and dropping the new one in place. Most of the time was spent sanding away corroded metal on the base to make a good fit. The information on the burner head says that the company has decided not to use a gasket under the head. I suggest that was a bad decision.
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people found this instruction helpful.
  • Scott from FORT WORTH, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people found this instruction helpful.
  • Barry from PORTERVILLE, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  t ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry
Was this helpful?
Thank you for voting!
Oven will not light up or will take multiple try
3 of 3 people found this instruction helpful.
  • charles from elmhurst, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Disconnected the oven from the wall outlet. Removed the bottom panel of the oven to reach the parts. Reached in the thight spot (not for a big guy)to unscrew the old igniter. Installed the new one. Plug the oven back. Turn the oven on bake at 350. Oveb lighted up in 5 seconds ! Working great since then!!!
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people found this instruction helpful.
  • Mary from MEADVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
Leaking gas from sides of burner
3 of 3 people found this instruction helpful.
  • Homero from SEAGOVILLE, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
Counterclockwise turn old burner to remove. Unplug attachment wires. Replug wires place back in place turn clockwise. Done.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people found this instruction helpful.
  • Alan from SAN MATEO, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
Drawer Glide Was Broken
3 of 3 people found this instruction helpful.
  • Karen from Yuma, AZ
  • Very Easy
  • Less than 15 mins
Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.
Was this helpful?
Thank you for voting!
All Instructions for the 3468
121 - 135 of 787