3422 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The drum ice maker broke in half so it couldn't dependent the ice.
8 of 9 people
found this instruction helpful.
-
ROWENA from WIGGINS, MS
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I had removed the housing that the drum was in and taken the screws out to get to the broken drum. I removed it there was a set of 6 blades that crushed the ice that had to go back on the same order when I removed these I put them on a piece of wire in the order they came off (so I would get them back I the correct order). Then I reversed
... Read more
the order and reassembled it in the opposite direction . It was fairly easy to do. I'm a 68 year old disabled woman so if I could do it I'm sure you could to. Good luck. It cost me $14.00 if I had bought the whole assembly it would have been $150.00. So it was well worth my time and effort.
Read less
Was this helpful?
Thank you for voting!
ice maker quit making ice
8 of 10 people
found this instruction helpful.
-
Barry from Middletown, DE
- Easy
- 15 - 30 mins
-
Screw drivers
I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the proce
... Read more
ss for the install. It took about 25 minutes and i was back making ice.
Read less
Was this helpful?
Thank you for voting!
The basket hanger is plastic and the rack tips of the basket hanger are even more delicate. Replaced basmet hanger no problem. They were expensive i.e. $70.
8 of 10 people
found this instruction helpful.
-
Isaac from WARFIELD, VA
- Very Easy
- Less than 15 mins
-
Nutdriver
Unscrew 4 screws . Remove broken basket hangers. Install new basketo hangers. Screw in 4 retaining screws...
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
the burner knobs broke off
10 of 17 people
found this instruction helpful.
-
Belinda from Downey, CA
- Really Easy
- Less than 15 mins
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this helpful?
Thank you for voting!
Bearing broke
7 of 8 people
found this instruction helpful.
-
Walter from Hamilton, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Took off Door on Refr. and unscrewed Doorstop,
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.
removed doorstop with broken Bearing and replaced with new Parts. Took about 20 Minutes
including reattaching Door. A 10 year old can do it.
Was this helpful?
Thank you for voting!
Icemaker not pushing out ice
7 of 8 people
found this instruction helpful.
-
Andrew from SALEM, MA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all o
... Read more
f the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
Original Ice Maker quit working.
6 of 6 people
found this instruction helpful.
-
Gary from Azle, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness.
Installed the new one in reverse order and works like a champ.
Installed the new one in reverse order and works like a champ.
Was this helpful?
Thank you for voting!
Oven would stop heating after a few minutes of operation
6 of 6 people
found this instruction helpful.
-
John from Ashland, OR
- Easy
- Less than 15 mins
-
Pliers
Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull
... Read more
the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.
Read less
Was this helpful?
Thank you for voting!
my old ice maker leaked at the bottom
7 of 9 people
found this instruction helpful.
-
harry from terre haute, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.
Was this helpful?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
6 of 7 people
found this instruction helpful.
-
Caroline from South Windsor, CT
- Really Easy
- Less than 15 mins
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this helpful?
Thank you for voting!
Ice maker stopped working (Very oxidized residue)
8 of 14 people
found this instruction helpful.
-
Robert from Woodstock, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.
Was this helpful?
Thank you for voting!
A glass insert/shelf broke when were cleaning it.
7 of 11 people
found this instruction helpful.
-
David from Fairlawn, OH
- Really Easy
- Less than 15 mins
It was very simple-it is just an insert glass shelf above the vegetable drawers. But, it was fairly easy to identify on your website and delivered in about two days.
Was this helpful?
Thank you for voting!
Replace ice maker which was splashing water
5 of 5 people
found this instruction helpful.
-
John from PHOENIX, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Turn off ice maker
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Slide wire harness shield off connector
Disconnected harness
Loosened 2 wall screws
Remove old ice maker
Installed new one reversing process
Was this helpful?
Thank you for voting!