EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

3422 - Instructions

All Instructions for the 3422
1 - 15 of 592

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not work but the Broiler did
337 of 374 people found this instruction helpful.
  • James from Ferndale, MI
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and f ound this site that explained it was possible for the igniter to glow but if it was not drawing the correct amperage (because its resistance was too high) then the main brain would not allow the gas valve to open. So I took a look at the broiler and it had the same igniter. I measure the resistance of both of them and the oven igniters resistance was higher (don't rememeber the reading) then I moved the Igniter from the broiler to the oven and the oven worked from there it was just a matter of ordering the part. End of story except for I am still doing all the cooking on the barbecue outside.
Was this helpful?
Thank you for voting!
Broken ice maker
255 of 345 people found this instruction helpful.
  • Juan from Miami, FL
  • Really Easy
  • 15 - 30 mins
  • Socket set
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.
Was this helpful?
Thank you for voting!
Ice Maker Stopped Working
164 of 183 people found this instruction helpful.
  • JACK from MESA, AZ
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only p roblem was that the end of the wire adaptor did not fit through the existing hole in the rear of the frig. I used a utility knife to cut through the thin metal lining. That worked just fine. However, I could not cut through the insulation because I could not reach it through the small hole. The excess wire was supposed to be pulled through the hole and out through the back of the unit. So now the excess is between the wall of the freezer and the insulation. The unit is working wonderfully. In fact, it is making more ice than I can use. I am very pleased with the replacement unit. This is the 3rd ice maker that has been in this frig. All the others had a design flaw that had a leak in the rear of the unit. This caused all the ice to form into a big block. The replacement unit has not had this problem so far. Thank you for allowing me to explain my situation so that maybe others may benifit from my experience. Thank you. Jack
Was this helpful?
Thank you for voting!
Oven would'nt light
132 of 146 people found this instruction helpful.
  • Charles from Charlestown, RI
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The new igniter took only 45 minutes to install and supply's 3.6 A/C volts to the gas valve and the oven works fine.
Was this helpful?
Thank you for voting!
oven failed to light
71 of 79 people found this instruction helpful.
  • Beryl from Dawsonville, GA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
My son replaced the broiler igniter this spring, so I had a clue as to what was required. This was even easier and since I had back surgery recently & my husband was out of town that was a giant plus!

I unplugged the oven, removed the oven door, found the release latch and removed the oven floor. I then removed the 2 screws that held the igniter in place (I received this stove used and the igniter had evidently been replaced before as it was the same shorter version included in the kit). I pulled the igniter out then removed some insulation and tugged the connector out of the oven floor. I disconnected the igniter and plugged the new one in. I then replaced the connector in the floor, attached the igniter with the screws, replaced the insulation and did a test run (plugged in the oven & turned it on). That was successful so I put the floor back in and put the door back on.
Ta-Dah!
Was this helpful?
Thank you for voting!
Oven would not ignite
57 of 61 people found this instruction helpful.
  • Jerry from Paris, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
This repair project was too easy!...and cheap. Sears quoted the price of the igniter at $280 plus the service call and the item cost $41 on PartSelect. The part was received the next day after the order was placed...WOW! So easy, turn off the power to the oven, open the oven door, remove the oven racks and lift the bottom pan of the oven up from the back and set it aside. There you see the flat type igniter in plain view at the back of the oven. Remove two screws with nuts using a nut driver (I had trouble because the screws were corroded and I had to use some, um, force to get them out and swore a little too). Once the screws were out, pull the igniter elecrtic wires and connector from the entrance hole in the back after moving a little insulation out of the way. Release the connector plug and unplug the old igniter and simply plug in the new one. Find new screws and reinstall in reverse order. Be sure to push the connector and wiring back into the hole and cover with the insulation. Very easy job that anyone could do.
Was this helpful?
Thank you for voting!
Needed to replace oven door gasket.
58 of 69 people found this instruction helpful.
  • Lori from Scottsdale, AZ
  • Really Easy
  • Less than 15 mins
  • Pliers
First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.
Was this helpful?
Thank you for voting!
Ice maker wouldn't change from crushed to cubed ice
63 of 97 people found this instruction helpful.
  • robert from sioux falls, SD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There i s 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
Was this helpful?
Thank you for voting!
Light socket melted around bulb
66 of 108 people found this instruction helpful.
  • William from Alexandria, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.
Was this helpful?
Thank you for voting!
Ice maker died!
45 of 49 people found this instruction helpful.
  • John from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
  • Socket set
The repair for this was very simple, although it was a tight squeeze. The model I replaced the ice maker on was a side by side. First I removed the ice bucket so I could have more room to work with. Then I unscrewed 2 screws on the left side wall holding the ice maker in place. These screws had a 1/4" nut top on them so I used my socke t driver for this. Then a quick disconnect of the wiring harness. Very Simple. I did the reverse to install the new unit. Total time was around 5 minutes or so. I now have ice again.
Was this helpful?
Thank you for voting!
glow bar would light but oven would not light
39 of 42 people found this instruction helpful.
  • David from Van Nuys, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
I removed the rear access panel on the oven in order to get to the igniter wires. While testing the output voltage of the old igniter when on, I found that it was producing less than 3 volts ac. This was my clue that although the igniter glowed, it was going bad and needed to be replaced. I unpluged the oven, shut off the gas feed to the oven then removed the oven bottom pan (pull two push pins back, lift up and out) and removed the burner baffle wing nut with baffle. This gave easy access to the igniter and it's two mounting screws which i removed using a phillips screw driver. I unpluged the old igniter from the connector, pluged in the new one after routing it through the access hole from inside the oven to the back of the oven where the connector is located.
Mounted the new igniter, replaced the burner baffle, baffle nut, oven bottom, rear access panel cover, checked and turned on the gas, plugged the oven back in and sure enough it fired up right away. if you check the system of how your oven works and find the problem, it's easy to fix it yourself and save serious money...and look like a hero to the rest of the family.
Was this helpful?
Thank you for voting!
the Auger would not augerate, I was not able to use the ice dispenser.
42 of 55 people found this instruction helpful.
  • ESTEBAN from MCALLEN, TX
  • Really Easy
  • Less than 15 mins
It was very simple. I order the complete Ice Container with Auger. It is great that it is already assembled. I just took out the old one and slipped the new one in. It has been working great ever since. I am just sorry that I waited so long to order the part. It was already like four months that the Auger started to give out on me. Thank You for everything, especially the delivery time.
Was this helpful?
Thank you for voting!
Ice Maker stopped working
39 of 48 people found this instruction helpful.
  • Dennis from DEER LODGE, MT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Reviewed the video on your website and followed the directions to the letter. Great video
Was this helpful?
Thank you for voting!
Oven would not heat but broiler would.
37 of 43 people found this instruction helpful.
  • Edward from Sewickley, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
By undoing the bottom of the stoves back panel, you are able to remove the two knock outs and ben the panel up for complete access. Remove gas line and electrical connection (with stove unplugged and main gas valve turned off). Undo the mounting screws and replace unit following steps in revcerse.
Was this helpful?
Thank you for voting!
ice maker would not rotate out cube or crushed ice.
40 of 62 people found this instruction helpful.
  • David from Ponca City, OK
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position an d order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order
Was this helpful?
Thank you for voting!
All Instructions for the 3422
1 - 15 of 592