3422 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven would not light
29 of 30 people
found this instruction helpful.
-
Richard from Austin, TX
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
This oven was located in a rental house I own.
I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.
Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.
I nex ... Read more t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.
With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.
The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.
I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.
I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.
I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
I first removed the metal plate that covers the burners at the bottom of the oven. No tools required for this step.
Next I turned the oven to 300 degrees, waited 30 seconds and noticed that the igniter was glowing brightly, but the burners did not light.
I nex ... Read more t turned the oven controls off, pulled the plug, and set to work removing the 2 screws holding a plate to the back oven wall and the 2 screws holding the igniter to the burner. These last 2 screws had corrosion on them and I needed to use vise-grips to get a firm hold on them. During reassembly these screws no longer held firmly because the hole they threaded into was enlarged during disassembly.
With the screws loose I pulled the igniter and fished the wires connected to it through the opening until I saw the connector. I then pulled the stove out of its opening and saw that there was a easily removable metal cover over the wires, and I took it off.
The new igniter came with an incompatible plug, so I cut off the connector on the stove wiring and on the new igniter and used wire nuts to make the new connections. I kept the orientation of the old and new plugs the same way in case the wiring mattered, but that was just being safe. I don't know if the igniter cares which of its wires go to which wire on the stove.
I reinstalled the screws holding the igniter, and shoved short sections of the supplied wiring into the screw holes so that the screws would hold more tightly. I shoved the supplied insulation into the opening that the wires passed through, and reattached the cover at the back of the stove.
I shoved the stove back into its opening, turned the oven on and it lit within 15 seconds.
I was very happy with the result, and the product I ordered arrived on time, well packaged and I'm a very happy customer.
Read less
Was this helpful?
Thank you for voting!
The old ice maker had stopped working properly. The cycle was inconsistent, and inlet water would run over existing cubes in the tray, before they were dumped into the dispenser box.
29 of 31 people
found this instruction helpful.
-
Daniel from Baldwin City, KS
- Really Easy
- Less than 15 mins
-
Nutdriver
This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed
... Read more
from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!
Read less
Was this helpful?
Thank you for voting!
Ice Crusher Broke. Plastic in Ice Tray
36 of 54 people
found this instruction helpful.
-
Ronald from Dickson, TN
- Easy
- 15 - 30 mins
-
Screw drivers
Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...
Was this helpful?
Thank you for voting!
Ice maker quit working
27 of 35 people
found this instruction helpful.
-
Robert from SIOUX FALLS, SD
- Really Easy
- 30 - 60 mins
-
Nutdriver
Loosen two screws, unclip electrical connection, remove ice maker, remove l shaped leveling piece of metal from old one, put on new one. Install in reverse order. Hint.. when loosening two screws, use a mirror
Was this helpful?
Thank you for voting!
Old icemaker would not cycle to make ice.
24 of 26 people
found this instruction helpful.
-
David from Cedar City, UT
- Easy
- 15 - 30 mins
-
Nutdriver
I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply cur
... Read more
ved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.
Read less
Was this helpful?
Thank you for voting!
oven takes a long time to reach temp set point
23 of 25 people
found this instruction helpful.
-
Scott from Brooklyn Park, MN
- Really Easy
- 15 - 30 mins
-
Screw drivers
i need to replace the lower oven igniter about 2-3 years
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
unplug the oven
open the oven door half way then slide the door up
take out both racks
push the bottom pan away from you and lift up
one screw holds the igniter on
pull the wire out until you get to the electrical plug
disconnect
Was this helpful?
Thank you for voting!
The ice chute door didn't close all the timed
39 of 73 people
found this instruction helpful.
-
Shelby from Clinton, IL
- Easy
- 30 - 60 mins
-
Screw drivers
The door has nylon gear teeth that wore out and needed replaced. The ice chute came off very easy with 6 screws. I used a punch and pliers to remove the hinge pin. Then the door came off and the new one put on. Very easy. The part was ordered on Sunday and arrived on Tuesday.
Was this helpful?
Thank you for voting!
oven burner would not come on.
20 of 20 people
found this instruction helpful.
-
Theodore C. from Winsted, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I am a retired lp Gas service person so this was quite
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
simple for me. Replaced the oven Igniter. What amazed me I placed my order and had the Igniter less than 24 hours. thank you so much for the quick service.
Was this helpful?
Thank you for voting!
This was so easy
21 of 23 people
found this instruction helpful.
-
Michael from Montclair, CA
- Really Easy
- Less than 15 mins
We broke a door shelf bin on our brand new refrigetor. We ordered a new one, put it in in less than a minute and it is fixed good as new.
Was this helpful?
Thank you for voting!
Water in the ice bin freezing all the existing ice into clumps
20 of 23 people
found this instruction helpful.
-
John from Mount Royal, NJ
- Easy
- 15 - 30 mins
-
Nutdriver
You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2)
... Read more
1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.
Read less
Was this helpful?
Thank you for voting!
Ice actuator broke.
24 of 36 people
found this instruction helpful.
-
Tim from Liberty Township, OH
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced ice actuator.
Was this helpful?
Thank you for voting!
igniter would light----gas valve would NOT open
21 of 28 people
found this instruction helpful.
-
Robert from SALEM, IL
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
SHUT OFF GAS
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas
... Read more />CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER
disconnect FLEX LINE from gas PIPE
remove GAS pipe from rear of stove
remove rear panel
remove pre-shaped gas lines to burners and oven / broiler
separate dual control valve from pressure regulator
disconnect wiring from dual control valve
REASSEMBLE in OPPOSITE order
turn on gas
... Read more />CHECK ALL FITTINGS FOR POSSIBLE LEAKS
Turn on each BURNER - making sure EACH one lites
turn on oven - making sure that the OVEN igniter lites the OVEN
set control on BROIL
turn on broiler - making sure that the BROILER
igniter lites the BROILER
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't lite
20 of 27 people
found this instruction helpful.
-
E Blake from Dauphin Island, AL
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the b
... Read more
ack of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.
Read less
Was this helpful?
Thank you for voting!
oven comes on to temp but will not reheat to a new temp third time trouble with same range
17 of 18 people
found this instruction helpful.
-
william from newport, VT
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was
... Read more
on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you
will sure use you again if the need arises thank you
Read less
Was this helpful?
Thank you for voting!
Ice Would Not Work - But Water Disp Did
17 of 19 people
found this instruction helpful.
-
JAMES from HENDERSON, NV
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation
Was this helpful?
Thank you for voting!