3221 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven wouldn't heat.
3 of 3 people
found this instruction helpful.
-
Thomas from La Crescenta, CA
- Easy
- Less than 15 mins
-
Nutdriver
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pus
... Read more
hed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat/ turn on
3 of 3 people
found this instruction helpful.
-
Diane from NEW HAVEN, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first
... Read more
turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
Read less
Was this helpful?
Thank you for voting!
Oven ignighter no longer works
3 of 3 people
found this instruction helpful.
-
Barry from PORTERVILLE, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel t
... Read more
ool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Barry
Read less
Was this helpful?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
3 of 3 people
found this instruction helpful.
-
Scott from FORT WORTH, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Was this helpful?
Thank you for voting!
OVEN WOULD NOT HEAT
3 of 3 people
found this instruction helpful.
-
Mary from MEADVILLE, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Was this helpful?
Thank you for voting!
freezer compartment worked fine but very little cooling going to refrigerator section.
3 of 3 people
found this instruction helpful.
-
Lee from OZARK, AR
- Really Easy
- 30 - 60 mins
-
Screw drivers
Freezer worked great but no cooling to refrigerator section. Replaced with part ordered. Phillips head screw driver is all that is needed. Very easy to replace, it's plug and play. New part powered up neither the freezer nor the refrigerator. Went back to old part and atleast freezer still works. New part was no good from factory. The re
... Read more
placement part# matched the original. I attempted to contact PartsSelect but there was no response back.
Read less
Was this helpful?
Thank you for voting!
Oven taking to long to preheat.
3 of 4 people
found this instruction helpful.
-
Isaac from LATHRUP VLG, MI
- Very Easy
- 30 - 60 mins
-
Screw drivers
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Was this helpful?
Thank you for voting!
Oven burner would periodically go out and re-light
3 of 4 people
found this instruction helpful.
-
Richard from Merrimac, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- ... Read more Connect the new part
- Re-attach to the bracket with new screws.
Read less
Was this helpful?
Thank you for voting!
Freont Burners Of Both Units Had Rusted Though Over The Years Of Boilover.
3 of 4 people
found this instruction helpful.
-
Angelo W. from Chirfland, FL
- Really Easy
- Less than 15 mins
Lifted lid, removed old burner units, replace with new ones. In less than two min. Was back up and cooking.
Was this helpful?
Thank you for voting!
Stove top had burnt marks from long use
3 of 4 people
found this instruction helpful.
-
MEEWAN from BUENA PARK, CA
- Really Easy
- Less than 15 mins
Just replaced the top.
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
No tool or repair was needed.
Parts arrived earlier than promised, so it was awesome!
Was this helpful?
Thank you for voting!
The old thermostat broke
3 of 4 people
found this instruction helpful.
-
Gregory from Braintree, MA
- Really Easy
- Less than 15 mins
The installation was very easy.
The knob fit right into place and that was it.
No screws or tools were necessary.
There was a "D Shaped" slot in the back of the knob that slid right into the metal piece attached to the stove.
The delivery was very quick and the ordering process was very easy.
The knob fit right into place and that was it.
No screws or tools were necessary.
There was a "D Shaped" slot in the back of the knob that slid right into the metal piece attached to the stove.
The delivery was very quick and the ordering process was very easy.
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Oven would not ignite
2 of 2 people
found this instruction helpful.
-
Dominick from CLARKS SUMMIT, PA
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Very easy, video helped tremendously
Was this helpful?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
2 of 2 people
found this instruction helpful.
-
James from PEORIA, IL
- Very Easy
- Less than 15 mins
-
Screw drivers
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
Was this helpful?
Thank you for voting!