3221 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Could not turn the oven on or off.
7 of 7 people
found this instruction helpful.
-
Christine from Indio, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Lifted the top up, only a few inches as the possibality of kinking the gas line was a issue. Took two screws out and replaced the unit, threaded the thermostat down through the oven. It was a breeze. I am 68 year old woman and did I myself.
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Most importantly, the process of getting the part was amazing, ordered it in the AM and receiv ... Read more ed it the next day (no extra charge)and by miday the range was good as new. Great service!
Read less
Was this helpful?
Thank you for voting!
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't ignite
8 of 11 people
found this instruction helpful.
-
John from Caliente, CA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Parts came very quickly from PartSelect. Good service.
Was this helpful?
Thank you for voting!
thermostat went out
9 of 14 people
found this instruction helpful.
-
brenda from redding, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Had to take off burners and lift off top. Then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and removed old element. Then I did all steps in reverse to install new thermostat.
Was this helpful?
Thank you for voting!
the burner knobs broke off
10 of 17 people
found this instruction helpful.
-
Belinda from Downey, CA
- Really Easy
- Less than 15 mins
I put the 2 burner knobs on and now I have 4 working burners....Thanks for the quick delivery....
Was this helpful?
Thank you for voting!
Seal was fallinig off
7 of 8 people
found this instruction helpful.
-
Marilyn from Fresno, CA
- Really Easy
- Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.
Was this helpful?
Thank you for voting!
Oven floor panel was warped.
8 of 11 people
found this instruction helpful.
-
Cindy from Colton, CA
- Really Easy
- Less than 15 mins
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
Was this helpful?
Thank you for voting!
Frige evaporator fan became noisy then quit working & frige compartment became warm
6 of 6 people
found this instruction helpful.
-
Scott from Bonney Lake, WA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Came home one evening and found the refer compartment evaporator fan making a noisy/grinding noise. While waiting for the part to arrive the motor finally quit working and the frige lost its ability to cool, but the freezer still worked fine. This is the fan that is inside the frige between the refer & freezer compartments - NOT the fan m
... Read more
otor that is located in the bottom/rear next to the compressor. This grinding noise sounded like it was coming from inside the frige and could be easily heard under the vegetable trays and above the freezer compartment. To access this motor you need to go after it from inside the bottom of the frige compartment - there's NO need to remove the refer door. Pull the vegetable trays and remove the small phillips head screw located down in the lower air flow groove toward the front of the refer. Next, pry up & out the front white trim piece that runs the width of the frige. Once that piece is removed you can lift & slide back the whole lower frige trim/tray. Now lift out the large foam block compartment and you'll have complete access to the evaporator fan motor and the evap coils. Simply pull the fan motor assy out, still attached to the triangular bracket and disconnect the electrical pigtail. Next, pull the fan blade straight off the front hub, split & disassemble the motor bracket, & replace both fan motor grommets. Reverse the steps to reassemble the fan motor to the bracket and reinstall back in the bottom of the frige and plug in the electrical pigtail - the fan should (quietly) fire off instantly and begin the cooilng process. Reinstall the foam block, lower frige tray, front trim piece, reattach the phillips screw, close the door, and give it some time - it took our frige overnight to completely cool down. This is not a tough job, I spent more time figuring out how to access the motor then the actuall replacement. Hope these steps help to speed up your repair! And remeber Red Sox 4 Life!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Over wouldn't light.
8 of 12 people
found this instruction helpful.
-
Bob from South Beloit, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Saw that the igniter came on, but no gas flow.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Unpluge stove. Remover bottom of oven to have access to flow valve. Remored sheet metal cover.
Removed burner. Unpluged flow valve and removed it.
Was this helpful?
Thank you for voting!
30 year old gas stove needed a new burner assembly.
6 of 7 people
found this instruction helpful.
-
Caroline from South Windsor, CT
- Really Easy
- Less than 15 mins
We lifted up the stove top, slipped the burner assembly in. It fit! who knew that we could get a part to an old stove without the model number, just by looking at a picture of the part! Terrific!
Was this helpful?
Thank you for voting!
Bad Door Gasket.
6 of 8 people
found this instruction helpful.
-
Donald from Schuylkill Haven, PA
- Really Easy
- Less than 15 mins
-
Pliers
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
Was this helpful?
Thank you for voting!
Oven Wouldn't heat
9 of 17 people
found this instruction helpful.
-
Robert from Liberal, KS
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Removed a few screws to remove a coulpe of metal covers to ge to part. After that, it was pretty easy to replace the valve and igniter.
The thermostat was a breeze!! A few screws, a couple of wires, route the sensor, and you're done..
The thermostat was a breeze!! A few screws, a couple of wires, route the sensor, and you're done..
Other Parts Used:
Was this helpful?
Thank you for voting!
Noisy refrigerator
6 of 8 people
found this instruction helpful.
-
Eric from NEW YORK, NY
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I visually inspected the compressor and narrowed down the source of the noise to the freezer area. Then I removed the doors and the screws securing the divider panel. Next I removed the bottom panel of the freezer, the styrofoam insullation panel and the evaporator motor. The motor is mounted between two grommets. I replaced the gromme
... Read more
t facing the fan blades. The aluminum reflector below the styrofoam insulation panel had also come loose. I reattached it and reassembled the refrigerator in reverse order. The noise is gone!
Read less
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people
found this instruction helpful.
-
Lloyd from PITTSBURG, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
One element of number display did not light
7 of 11 people
found this instruction helpful.
-
Lawrence J from BENTON, AR
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
clock is in top of double oven. Dis-assembly and access to the clock was a puzzle. Four screws in the top of the oven were the solution. The clock panel then folded out and access to three plug-ins and four screws allowed access to the clock. remounted the clock with four screws and replaced plugs. (watch carefully order of wiring) Re-p
... Read more
ower on the oven and set clock. NOTE: Cover said Magic Chef but Label said MayTag
Read less
Was this helpful?
Thank you for voting!