3221 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Faulty bulb receptacle
10 of 20 people
found this instruction helpful.
-
Kenneth from Lynchburg, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
Stove seal fell apart
5 of 6 people
found this instruction helpful.
-
Teresa from Washougal, WA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.
Was this helpful?
Thank you for voting!
Gas manifold had holes in it.
5 of 6 people
found this instruction helpful.
-
Mr. J.C. from Haines City, FL
- Really Easy
- Less than 15 mins
Removed locking wire from bottom burner assembly then I pulled the element out and replaced with the new one.
Was this helpful?
Thank you for voting!
Freezer door would not close all the way.
4 of 4 people
found this instruction helpful.
-
Paul from LINCOLN, DE
- Very Easy
- Less than 15 mins
-
Socket set
Pulled the door off easily and noticed that the spacer on the Center hinge was ground down to nothing and that a small screw in the bottom plate of the door was half way out. This screw would catch on the cabinet Center hinge bracket and stopped the door from closing. Problem was solved by tightening the screw and putting in a new "spac
... Read more
er" that kept the small screws from contacting the Center hinge bracket. The freezer door now closes like new.
Read less
Was this helpful?
Thank you for voting!
A high flame was coming out of the side of the burner
5 of 7 people
found this instruction helpful.
-
KAY from BRIDGEPORT, CT
- Really Easy
- Less than 15 mins
Easy......pulled out the old one easily and popped in the new one.......saved a lot of money...no repair bill for either diagnostic fee or assembly fee ...No mark up for the part either. Very happy mom!
Other Parts Used:
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
The oven igniter lit up but the valve wouldn't release the gas to ignite.
4 of 4 people
found this instruction helpful.
-
John from Wisconsin Rapids, WI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured wi
... Read more
th the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
Read less
Was this helpful?
Thank you for voting!
Oven did not light---only glowed
5 of 7 people
found this instruction helpful.
-
PEREZ from YONKERS, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I thought that the initial problem based on the users manual may had been the thermostat.
Removal of the old unit and installation of the new one was quite simple.
The only time lag was cleaning some of the surrounding areas of the oven as worked progressed.
As it turned out though, the problem wasn't the thermostat, but ra ... Read more ther the igniter.
But, that was a fairly easy job as well!
Removal of the old unit and installation of the new one was quite simple.
The only time lag was cleaning some of the surrounding areas of the oven as worked progressed.
As it turned out though, the problem wasn't the thermostat, but ra ... Read more ther the igniter.
But, that was a fairly easy job as well!
Read less
Was this helpful?
Thank you for voting!
oven would not turn on flame
6 of 10 people
found this instruction helpful.
-
Michael from Secaucus, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment.
... Read more
Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
Read less
Was this helpful?
Thank you for voting!
oven wouldn't light
4 of 5 people
found this instruction helpful.
-
peter from marine city, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to f
... Read more
ully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!
Read less
Was this helpful?
Thank you for voting!
oven door gasket torn
4 of 5 people
found this instruction helpful.
-
Ovide N from Abbeville, LA
- Really Easy
- Less than 15 mins
ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job
Was this helpful?
Thank you for voting!
Broken levelling leg
5 of 8 people
found this instruction helpful.
-
Linda from Oneida, NY
- Really Easy
- Less than 15 mins
Took the old levelling leg out and screw the new one in.
Was this helpful?
Thank you for voting!
Smelled burning plastic
4 of 5 people
found this instruction helpful.
-
JOHN from PERKINSTON, MS
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the cardboard cover from the back of the fridge. I was not sure where to begin then the compressor kicked on and a flame came from the bottom of relay that mounts to compressor, so i unplugged fridge and let cool .I removed part that burned and looked on this site to identify what it is. The part has been updated to a new design
... Read more
which is now a white plastic. I also replaced run capacitor .Put the new parts on and it was back to working .The sleeve that comes with the new run capacitor didn't fit under the lock wire clip so i left off.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud motor noise emanating from inside the refrigerator (not the compressor or external fan).
3 of 3 people
found this instruction helpful.
-
Chong from NEW YORK, NY
- Easy
- Less than 15 mins
-
Screw drivers
My GE GDS18SBPBLSS is now 21 years old (they do not make them like they used to) so I took extra time to not break any of the brittle old plastics. For this replacement you will only need a Phillips head screwdriver.
Parts list:
2 x PS284959 Fan Motor Grommet
1 x PS2359960 Evaporator Fan Motor Assembly
• Th ... Read more e first thing you want to do is to unplug the unit refrigerator to prevent any shorts or the fan from starting while you are handling it.
• The evaporator motor is in the refrigerator section, so leave the freezer door shut to preserve the temperature.
• Open the refrigerator door as much as possible and take out the two vegetable/fruit drawers. If your door is right next to a wall and you cannot open it more than 90 degrees, take the drawer furthest from the door hinge first. Then take out the remaining drawer and gently shimmy the center plastic rail guide to allow you to take it out diagonally.
• The front lip of the floor of the refrigerator is clipped in, so pull the plastic trim forward to remove it. If it does not move, lift the center of the plastic trim piece in front of the screw a bit to convince it loose, but it prying it upwards is not advisable because the ends are under the side walls.
• Once the trim piece is removed, remove the Phillips head screw.
• Pull the plastic floor of the refrigerator towards the front and then up to remove it.
• A large foam block secured down with tape needs to be removed next. Once the tape is loosened, lift the foam out carefully with vapor barrier attached under it. Watch for the two foam pieces at the back wall on each side. If they fall off and drop, find them in the freezer later.
• The fan assembly and bracket will be in view, and my suggestion is to take a photo. This way, you know how it should look when it comes time to reassemble everything.
• To the left rear is a small foam block that is taped down. Removing that will reveal the connector clip for the fan motor’s power line that you squeeze the sides to disconnect. Pull the motor wire out of the foam guide.
• Lift the motor bracket assembly out – it is not attached to anything and sits on the foam block.
• Carefully pull the fan blade off by pulling it straight along the motor shaft.
• Undo the rear motor bracket by unscrewing the two Phillips head screws – the right rear motor bracket screw holds the wire guide in. When undone, take the guide off the wire.
• Once the rear bracket is removed, discard the two motor grommets and the motor.
• Put in the new motor with the new motor grommets into the bracket and screw in the left rear screw.
• Clip on the wire guide on to the new motor wiring and then finish mounting the motor with the right rear screw with the wire guide in place.
• Clean off the fan blade thoroughly before pressing into the shaft. Once on, spin the fan to see if it rotates smoothly and easily. Note: Avoid pressing the fan blade too far down as you do not want it to contact the grommet.
• Place the assembly back into the foam block – use the photo from before as a guide if needed.
• Route the motor cable through the foam groove and clip it into the power connector.
• Plug the refrigerator back in to see if the fan spins and to see that there are no issues. If there are no problems, unplug the unit again and continue the reassembly.
• Place the small foam block back into the rear left to cover the connector area.
• While making sure the vapor barrier is positioned correctly above the coils, put the foam block back into place.
• Clean the plastic floor of the refrigerator and then slide it into place, making sure the back and side are flush. Use the screw hole to align the floor properly and then screw the Phillips head screw back in.
• Clean the front trim piece and then slide it back into place.
• Put the drawers back in.
• Plug the refrigerator back in and leave the door closed for a while so the unit cools the internal temperature back down.
Parts list:
2 x PS284959 Fan Motor Grommet
1 x PS2359960 Evaporator Fan Motor Assembly
• Th ... Read more e first thing you want to do is to unplug the unit refrigerator to prevent any shorts or the fan from starting while you are handling it.
• The evaporator motor is in the refrigerator section, so leave the freezer door shut to preserve the temperature.
• Open the refrigerator door as much as possible and take out the two vegetable/fruit drawers. If your door is right next to a wall and you cannot open it more than 90 degrees, take the drawer furthest from the door hinge first. Then take out the remaining drawer and gently shimmy the center plastic rail guide to allow you to take it out diagonally.
• The front lip of the floor of the refrigerator is clipped in, so pull the plastic trim forward to remove it. If it does not move, lift the center of the plastic trim piece in front of the screw a bit to convince it loose, but it prying it upwards is not advisable because the ends are under the side walls.
• Once the trim piece is removed, remove the Phillips head screw.
• Pull the plastic floor of the refrigerator towards the front and then up to remove it.
• A large foam block secured down with tape needs to be removed next. Once the tape is loosened, lift the foam out carefully with vapor barrier attached under it. Watch for the two foam pieces at the back wall on each side. If they fall off and drop, find them in the freezer later.
• The fan assembly and bracket will be in view, and my suggestion is to take a photo. This way, you know how it should look when it comes time to reassemble everything.
• To the left rear is a small foam block that is taped down. Removing that will reveal the connector clip for the fan motor’s power line that you squeeze the sides to disconnect. Pull the motor wire out of the foam guide.
• Lift the motor bracket assembly out – it is not attached to anything and sits on the foam block.
• Carefully pull the fan blade off by pulling it straight along the motor shaft.
• Undo the rear motor bracket by unscrewing the two Phillips head screws – the right rear motor bracket screw holds the wire guide in. When undone, take the guide off the wire.
• Once the rear bracket is removed, discard the two motor grommets and the motor.
• Put in the new motor with the new motor grommets into the bracket and screw in the left rear screw.
• Clip on the wire guide on to the new motor wiring and then finish mounting the motor with the right rear screw with the wire guide in place.
• Clean off the fan blade thoroughly before pressing into the shaft. Once on, spin the fan to see if it rotates smoothly and easily. Note: Avoid pressing the fan blade too far down as you do not want it to contact the grommet.
• Place the assembly back into the foam block – use the photo from before as a guide if needed.
• Route the motor cable through the foam groove and clip it into the power connector.
• Plug the refrigerator back in to see if the fan spins and to see that there are no issues. If there are no problems, unplug the unit again and continue the reassembly.
• Place the small foam block back into the rear left to cover the connector area.
• While making sure the vapor barrier is positioned correctly above the coils, put the foam block back into place.
• Clean the plastic floor of the refrigerator and then slide it into place, making sure the back and side are flush. Use the screw hole to align the floor properly and then screw the Phillips head screw back in.
• Clean the front trim piece and then slide it back into place.
• Put the drawers back in.
• Plug the refrigerator back in and leave the door closed for a while so the unit cools the internal temperature back down.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!