3221 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Refridgerator and Freezer were not cooling.
2 of 2 people
found this instruction helpful.
-
Frank from VERO BEACH, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Installing the part repaired the fridge and freezer immediately.
Was this helpful?
Thank you for voting!
freezer stoped freezing
2 of 2 people
found this instruction helpful.
-
paul from ENDICOTT, NY
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE
... Read more
OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.
Read less
Was this helpful?
Thank you for voting!
The problem was exactly what was described on your site.
2 of 2 people
found this instruction helpful.
-
William from FREELAND, MI
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pretty much did the repair the same way the video described it. I first turned off the gas valve and disconnected the power. Then removed the two screws holding in the burner tube and removed it. Then I unplugged the old igniter. The screws were a bit corroded so I gave them a little spray of liquid wrench. They came right out them. Aft
... Read more
er removing them I replaced the igniter plugged it in. Then I put the wire through the hole in the wall of the oven. Replaced the insulation that was included in the kit. Replaced the burner tube on the venture. And reinstalled the screws. It was pretty cut and dry. The glow plug had the burner fired up in 15 seconds.
Read less
Was this helpful?
Thank you for voting!
Igniter glowed but oven would not light
2 of 2 people
found this instruction helpful.
-
Richard from West Mifflin, PA
- Easy
- Less than 15 mins
-
Nutdriver
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Was this helpful?
Thank you for voting!
Oven Was Not Getting Hot
3 of 5 people
found this instruction helpful.
-
Joe from Duarte, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
Was this helpful?
Thank you for voting!
floor panel heavily stained and warped
3 of 5 people
found this instruction helpful.
-
Joel from Monroe, NY
- Really Easy
- Less than 15 mins
slide latches in rear of floor panel forward and remove.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Tom from Greenville, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the ol
... Read more
d ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!
Read less
Was this helpful?
Thank you for voting!
oven would take a very long time to warm
2 of 2 people
found this instruction helpful.
-
Barry from East Islip, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like ... Read more new .
Read less
Was this helpful?
Thank you for voting!
oven wouldn't heat
2 of 2 people
found this instruction helpful.
-
Dana from Windchester, IN
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine
Was this helpful?
Thank you for voting!
1960's oven door gasket fell apart, actual gasket not available any more
2 of 2 people
found this instruction helpful.
-
Mary from WINCHESTER, MA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
Was this helpful?
Thank you for voting!
old bulb fused into old socket.
5 of 11 people
found this instruction helpful.
-
Michael from Reno, NV
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
removed old socket and replaced.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
I was VERY pleased with Partselect. Easy to find part, it was in stock and fast delivery.
Was this helpful?
Thank you for voting!
igniter burned out
2 of 2 people
found this instruction helpful.
-
David from Milton, MA
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
Was this helpful?
Thank you for voting!
oven would not light
2 of 2 people
found this instruction helpful.
-
gary from covington, LA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.
Was this helpful?
Thank you for voting!
The face of Temperature marking position is different from my old knob
2 of 2 people
found this instruction helpful.
-
Mona from BROOKLYN, NY
- Very Difficult
- More than 2 hours
I cannot use the thermostat knob on my “Magic Chef - With Uniburners” stove because the temperature markings are off.
The “WARM” on the new knob is “OFF” on my old knob!
What should I do to make the new knob works with my stove? Please advise.
Thank you..
The “WARM” on the new knob is “OFF” on my old knob!
What should I do to make the new knob works with my stove? Please advise.
Thank you..
Was this helpful?
Thank you for voting!