3221 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
igniter glowed but oven would not light
2 of 3 people
found this instruction helpful.
-
edward from euclid, OH
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
It looked like an easy fix. the igniter had a plastic clip. A simple R&R. Removed old igniter from its mount, removed plate to get access to wires, removed insulation. Tried to pull the old wires out of its location. It was hung up and I spent 1/2 hr. trying to free it. No go. I thought I'd have to remove oven from its cabinet. I removed
... Read more
six screws and it would not come forward. I felt the under side of the oven thru lower door of cabinet and found out that was where gas was connected. No way was I disconnecting the gas. Pushed oven back in, reinstalled screws and decided to cut old wires and splice in the new igniter. WENT BACK AND READ THE INSTRUCTIONS! Supplied were 4 ceramic wire nuts. Then the light bulb went on! OKAY! I got a marker and marked the top wire on the old igniter to identify it after I cut the wires as close to the back of the old igniter as I could with a pair of side cutters. I then cut the wires as close as I could to the plastic clip on the new igniter. Striped off 3/8 in. from all wire ends and spliced the wires together using the wire nuts. I stuffed the wires as far as possible back into the hole they came from, replaced all old and some new insulation into the hole. The supplied cover would not work, screw holes would not line up and would have fit poorly. I reused the old hole cover. Screwed new igniter to its mount. Turned on the oven and thought I screwed up. I waited about 30 seconds before I saw it start to glow. WHEW! I got it right! After a few more seconds, the gas came on and the oven burner ignited. The really hard part was putting the oven door back on its mount. That door was heavy and wouldn't line up on the first try.......
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Maybe if I read the instructions thoroughly the first time before I started, I could have cut my time in half and saved a lot of cussin'. CUTTING THE WIRES WAS AN "OPTION"! That's why they supplied the ceramic wire nuts!....... Dinner is in the oven right now. Smells good!
Read less
Was this helpful?
Thank you for voting!
oven would not turn on
2 of 3 people
found this instruction helpful.
-
Robert from Clymer, NY
- Easy
- 15 - 30 mins
-
Screw drivers
I first removed oven racks.then I removed bottom of oven by sliding locks,then lifting out bottom.Next I removed screw holding e. control cove,then removed cover.Igniter plug was exposed,I then unpluged egniter. I next removed 2 screws holding burner and igniter .I removed igniter and burner as a unit. removed 1 screw from igniter,and rep
... Read more
laced igniter on burner.Then assembled every thing in reverse order,and tested Oven worked perfectly.
Read less
Was this helpful?
Thank you for voting!
I needed a broiler pan
4 of 9 people
found this instruction helpful.
-
Rhoda P. from Secaucus, NJ
- Really Easy
- Less than 15 mins
I took the broiler pan out of the shipping container and put it in the oven.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken burner knobs on stove.
2 of 3 people
found this instruction helpful.
-
Barbara L. from Tewksbury, MA
- Really Easy
- Less than 15 mins
Just replaced the old burner knobs with the new !!!
Was this helpful?
Thank you for voting!
Range burner drip pans were rusted and old
3 of 6 people
found this instruction helpful.
-
Billye from San Antonio, TX
- Really Easy
- 15 - 30 mins
The repair was super simple, just remove the drip pan and place new one.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
The hard part was finding the drip pan for such an old model appliance. I had shopped locally here in San Antonio with no luck.
I was very happy to find them (exact match) at Part Select and the price was very reasonable. I'll use Part select in the fu ... Read more ture for needed parts.
Read less
Was this helpful?
Thank you for voting!
Install valve knobs
3 of 6 people
found this instruction helpful.
-
Donald from Peebles, OH
- Really Easy
- Less than 15 mins
This was not a difficult task. I just slid the valve knob on the shaft, repair was complete. This was a very easy diy project.
Was this helpful?
Thank you for voting!
rusty drip trays
2 of 3 people
found this instruction helpful.
-
Pam from Grand Ledge, MI
- Really Easy
- Less than 15 mins
finally after years of searching for trays of this size with no luck in local stores, I was able to find and purchase 2 sets, one set for my daughter, which we were able to put in place to clean up our stoves and make them more appealing . Thank-you for your prompt service.
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
oven would not heat up fully, smelled of gas.
1 person
found this instruction helpful.
-
Brian from Spotswood, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.
Was this helpful?
Thank you for voting!
Gas would come on, would not ignite. Oven not heating.
1 person
found this instruction helpful.
-
Karen from DAYTON, OH
- Very Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Super easy. Turn off gas and unplug. Lift door off hinges, just pull up on it. Take racks out. Lift floor of oven out. You may need to release clips in the back of the oven, but mine were not engaged. Remove wing nut from shield plate and lift plate off. Using nutcracker, or Phillips screwdriver, remove screws holding the igniter to the
... Read more
brace plate. Carefully pull wires from the back of the oven wall. Carefully unplug the old part. Carefully plug in the new part. Feed wires back into the oven wall and install fiberglass padding. Replace screws, shield plate, wing nut, oven floor, oven racks and door. Door just slides back onto hinges. Watch the video on parts elect. Couldn't have been easier. Saved $500 on replacing my oven. $40 for DIY repair. Awesome!!!
Read less
Was this helpful?
Thank you for voting!
Start relay burned
1 person
found this instruction helpful.
-
Carlos from Copper Canyon, OK
- Very Easy
- 15 - 30 mins
-
Screw drivers
Unplug the refrigerator removed the condenser/ compressor cover back bottom on fridge, remove the relay from the compressor took off the two wires, replace with new relay
Was this helpful?
Thank you for voting!
Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.
1 person
found this instruction helpful.
-
Mz from COLUMBIA, ME
- Very Easy
- Less than 15 mins
-
Pliers
Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
35 year old range. grates too dirty to clean. Parts Select had exact replacement grates. Perfect fit.
1 person
found this instruction helpful.
-
FRANCES from AFFTON, MO
- Very Easy
- Less than 15 mins
Easy, removed from box, put in place on range. Happy customer. Good company to find exact replacement parts.
Was this helpful?
Thank you for voting!
my knobs were broken on 30 year old range
1 person
found this instruction helpful.
-
Larry from LAWTON, MI
- Very Easy
- Less than 15 mins
-
Pliers
I took a pair of channel locks pulled the old one off pushed the new one on they look really nice and was glad they had the parts for such an old stove. thank you,now my hubby is glad so he doesn't have to buy a new stove.
Was this helpful?
Thank you for voting!