3186 - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
2 of 2 people
found this instruction helpful.
-
Kaye from San Francisco, CA
- Really Easy
- Less than 15 mins
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this helpful?
Thank you for voting!
Old end cap broke.
2 of 2 people
found this instruction helpful.
-
Travis from North Quincy, MA
- Really Easy
- Less than 15 mins
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this helpful?
Thank you for voting!
The above door End Cap broke.
2 of 2 people
found this instruction helpful.
-
John from Northglenn, CO
- Really Easy
- Less than 15 mins
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this helpful?
Thank you for voting!
light wouldn't come out of socket
3 of 5 people
found this instruction helpful.
-
Joyce from Tacoma, WA
- Really Easy
- Less than 15 mins
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this helpful?
Thank you for voting!
Broken shelf retainer bar end cap.
2 of 2 people
found this instruction helpful.
-
Ruchik from Bronx, NY
- Really Easy
- Less than 15 mins
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before orde
... Read more
ring. Otherwise, the entire process from order to finish took about 3 days.
Read less
Was this helpful?
Thank you for voting!
The plastic parts that hold the brackett to the shelf were broken.
2 of 3 people
found this instruction helpful.
-
Sammy from Farmington, NM
- Really Easy
- Less than 15 mins
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Also the part came so quickly it was al ... Read more most as good as buying it here in town. Thanks. Donna Bingham
Read less
Was this helpful?
Thank you for voting!
door shelf bar was bent and no longer holding in items
2 of 3 people
found this instruction helpful.
-
jamie from san clemente, CA
- Really Easy
- Less than 15 mins
we ordered new bar, cut to fit with instructions, and voila! easy!
Was this helpful?
Thank you for voting!
Light would no longer turn on
3 of 6 people
found this instruction helpful.
-
paypal_shipping_address from Ripon, CA
- Really Easy
- Less than 15 mins
-
Pliers
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this helpful?
Thank you for voting!
Light out
2 of 3 people
found this instruction helpful.
-
Jodi from Benton Harbor, MI
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $
... Read more
120 service call.
Read less
Was this helpful?
Thank you for voting!
bottom of gasket deteriorated and let in warm air
2 of 3 people
found this instruction helpful.
-
Lawrence from O'Fallon, IL
- Really Easy
- 30 - 60 mins
i pulled the old gasket off, and placed the new one in place, starting at the corners. then i lined up the insert in the gasket with the gap where it is to go and ran my fingers along the gasket, pressing in with my thumb.
Was this helpful?
Thank you for voting!
needed to replace the gasket because it had become brittle
2 of 3 people
found this instruction helpful.
-
tara from cumming, GA
- Easy
- 15 - 30 mins
My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.
Was this helpful?
Thank you for voting!
the plastic part had broken and wouldn't support drawer
2 of 3 people
found this instruction helpful.
-
Beverly from Pensacola, FL
- A Bit Difficult
- More than 2 hours
-
Screw drivers
Replacing the new part wasn't hard, just very time consuming and frustrating. I had to remove two-thirds of the shelving of refrigerator as broken drawer slide was on the bottom and I had to have room to remove old and replace new. Of course, then I had to CLEAN all the drawers and shelving before replacing them and then, because they w
... Read more
ere fresh and clean, I had to remove the other third of shelving and wash and replace it. So, it was an hour-long or more time. I love your business, and had no idea I could get so many parts for old applicance and replace them myself, and I am a 70-year-old woman! This was the 2nd time to use your site and I will return to it again when needed. Thanks for prompt and reliable service and a site that makes it easy for a neophyte like me to find the broken part ! Keep up the good work.
Read less
Was this helpful?
Thank you for voting!
Old defrost Heater buckled up and bunted out due to no cut out in metal bracket design
1 person
found this instruction helpful.
-
Richard from LONG IS CITY, NY
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I watched videos of the modern refrigerators and figured out how to do my model by taking my time watching as many videos that pertain to my refrigerator I finally I expose the evaporator I noticed that the defrost heater was buckled up and totally disintegrated and slowly took my time looking at the screws I took it out and I didn't have
... Read more
to do
disassemble bottom of the freezer to replace the part, you definitely had to have common sense and to be mechanically inclined to do this repair otherwise it was easy
disassemble bottom of the freezer to replace the part, you definitely had to have common sense and to be mechanically inclined to do this repair otherwise it was easy
Read less
Was this helpful?
Thank you for voting!
The left side rail had broken where the screws secure it to the delidrawer
1 person
found this instruction helpful.
-
Cathleen from LOS ANGELES, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers
The left side rail had broken where the screws secured it to the drawer. Your replacement part fits perfectly! In fact the drawer slides easier now than it did before!
I’d read that I should keep the original screws. They were a bit too big to fit the replacement part. A trip to the hardware store solved the problem and the ne ... Read more w slide is now in place.
Your description and drawings for this part really helped me out!
Thank you so much for having this service available for my old but trusty refrigerator!
I’d read that I should keep the original screws. They were a bit too big to fit the replacement part. A trip to the hardware store solved the problem and the ne ... Read more w slide is now in place.
Your description and drawings for this part really helped me out!
Thank you so much for having this service available for my old but trusty refrigerator!
Read less
Was this helpful?
Thank you for voting!
Fresh food door gasket was torn and no longer sealing in cold air and warm air out
1 person
found this instruction helpful.
-
Francois from BAINBRIDGE IS, WA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Removed old gasket and installed new gasket, per the video instructions on the PartSelect website. Instructions were clear and accurate. I wondered if the new seal would fit snuggly and securely, but no problems. The seal holds the door closed more firmly than the old seal did. So far, so good!
Was this helpful?
Thank you for voting!